Quick Question!

Have you ever purchased from PartSelect.com before?

Models > MVH250W (P1323204M) > Instructions

MVH250W (P1323204M) Amana Microwave - Instructions

All installation instructions for MVH250W parts

These instructions have been submitted by other PartSelect customers and can help guide you through the microwave repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the MVH250W
31-45 of 90
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Turn table did not consistently turn during microwave oven operation.

  • Customer: Jeffrey from BREMERTON, WA
  • Difficulty: Very Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 2 people found this instruction helpful
Using fingers, the old turntable roller guide was pulled up off the motor shaft. The plastic roller guide shaft coupler was found to be broken, allowing the motor shaft to spin without turning the roller guide. The hole in the floor of the oven was inspected, and no broken pieces were found which could interfere with the new roller guide. The new roller guide was then gently pressed down over the motor shaft. Very easy.

No power to any microwave functions

  • Customer: Richard from CALIFORNIA, KY
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 2 of 2 people found this instruction helpful
Access is via RT. SIDE Panel as you face microwave. There are three screws on the bottom right edge to loosen. After that the side panel slips down and off. the fuse is located in the rear near where the power cord comes in. It is the white ceramic tube 1/4" in dia. and 1-1/2" long. Pull it out like any fuse and replace with new one. Reassemble and you are done!

original rotater broke

  • Customer: Cynthia from Wylie, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 3 of 5 people found this instruction helpful
Replaced the broken piece with the one purchased at Partselect.com. I was concerned that the part would not be correct since all we did was enter the model number of the microwave. PartSelect.com was really easy to use and sent the correct part. Thanks so much for making this process easy.

light bulb burned-out

  • Customer: Pablo from Burlingame, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 9 of 23 people found this instruction helpful
screwed in new bulb

Plastic latch to lock the microwave door broke.

  • Customer: Richard from Arlington, VA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 6 of 14 people found this instruction helpful
Did an online search for repairs and found PartSelect. Simple to order the part and had it installed myself less than a week later. Thank you!!

Stem broken off the turntable base so the turntable wouldn't rotate

  • Customer: Joellyn from Olathe, KS
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 3 people found this instruction helpful
Removed the broken plastic base that the glass turntable sets on and put in the new plastic base. Took 5 seconds max! The part arrived in about 24 hours! Great service!

Tray got chipped on the corner

  • Customer: Mary Lee from LK FOREST PK, WA
  • Difficulty: Very Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 1 people found this instruction helpful
ordered a new tray

Burned out light bulb which lit the surface of the range.

  • Customer: Michael J from LORAIN, OH
  • Difficulty: Very Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
Unscrewed glass panel, removed old bulb, cleaned glass panel and installed new bulb. Screwed panel back into place.

Turntable roller shaft was broken.

  • Customer: Juan from Los Angeles, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 4 people found this instruction helpful
Put in the new part, took less than a minute...

Crack in the lower left corner of the outer door panel

  • Customer: Nat from Raleigh, NC
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 2 of 4 people found this instruction helpful
Thankfully, one of your customers had submitted the repair description. I followed along as best I could. I would add to the description that one should pay attention to the details as the door is taken apart -- it can only be put back together in one way. My door was a bit stuck together in a couple places making it a bit more difficult to disassemble. One last item, after removing the handle, the door pivots off the door structure at the hinge end -- I struggled with this a bit because my handle was stuck on.

Door panel was broken

  • Customer: Eric from Nashville, NC
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 3 of 7 people found this instruction helpful
I removed the inside plate and removed the two screws that held the handle on. I removed the existing door panel and replaced it with the new one. I then replaced the handle with the two screws and snapped the inside plate back into place. Getting the handle to realign once the new door panel was in place was the trickiest part. This repair cost me $40 when a new microwave would have cost over $200.

plate in microwave would not turn

  • Customer: Julie from Madison, MS
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
took out plastic piece under plate (that was broken) and placed new one in the hole. No tools req'd. Works like new.

Glass Cooking Tray Broke

  • Customer: Mitchell from Henderson, NV
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 5 people found this instruction helpful
Opened Box and Replaced Part......No Problem!

One of the shelf plastic holder was broken

  • Customer: Craig from Swansea, MA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 3 of 8 people found this instruction helpful
I was able to find the part on line and within a few days received the part and installed it with no problems thanks to the website drawing information.

Turntable Stop Moving

  • Customer: Debbie from Franklin Park, IL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
Replaced turntable support with new unit.
All Instructions for the MVH250W
31-45 of 90