MV-1525B LG - Instructions

Unplug the unit before servicing. Need phillips screwdriver. Open door. Use step ladder to access and remove 2 small screws from top of the room air diffuser at top of unit. Slide diffuser slightly to the left to align the diffuser's plastic tab on the left side to rotate toward you. (The wires for the front control panel are at the far left side of this difuser, but difuser is slotted for easy removal). Once the difuser is removed you will see 1 screw at the top that secures the pannel cover on the left side of the unit. Remove screw and slide this panel slightly up and out. This exposes the plastic frame that holds the upper and lower door switches. To locate the door switches and observe how they work, close and open the door and watch the door (bayonets) open and close the micro switches. Do the (red) buttons on top of the switches move up and down when the door bayonets push and release? If the buttons do not "pop" up when opened the switch is defective. The switch frame is secured with 2 screws. Remove screws and rotate the unit out for easy access to the micro switch(s). The internal (spring?) on my unit that is suposed to allow the red (visible) button on top of the switch to "pop" up when the door is opened was broken. Carefully pry the switch outward while being careful to lift the plastic holder-piece that holds the switch in place. Be careful, there is a small pin on the frame, so rotate the switch OUT toward you while lifting (carefully) the plastic holder-piece (you will see it on top of the switch). You can use an ohm meter to test the continuity of the switches. But if the buttons don't "pop" they are defective. Replace switch and reassemble.

ordered on the part select web site, came quickly, order was correct

new glass tray

Watched a couple of repair videos on Youtube by searching for the model number. Found out what to do in order not to get shocked by the powerful capacitor.
Ordered the two switches (To be sure, I could have ordered a third switch as suggested in the videos.)
Bought a tamper-proof star bit to get the cover off. Followed the directions to replace the switches. - I broke the harness and had to use some super glue, but it's all good. I should have removed the harness instead of trying to get a switch out while it was still in place.
It's all back together, and the wife is happy!!

The wrong part was under $20. When I found out I had to replace the whole door for $150. I decided DYI was the way to go. I used JB weld and the door looks and works like a charm. Give plenty of time to cure all water needs to be cured out if exposed to microwaves. No problems so far.

I unplugged the microwave. I did watch a YouTube video to see how the plastic frame around the door could be removed. I used a putty knife to pry it off. The spring was still in good shape, so I hooked it up to the new latch/locker part and onto the microwave. This was just a little time consuming because I was trying to be careful so I wouldn't break anything on the new part. The plastic frame clicked right back on. I plugged the microwave in and it worked right away. If I can do it, you can do it. Sure beat buying a new microwave. Great experience.

Removed some cosmetic panels. Removed the assembly with micro switches. Examined the faulty switch by checking the clicking action of switch. Two others were ok by this method. Replaced the switch with new one. Works fine so far. Thanks to web site and YouTube videos.

TOOK OUT ALL SCREWS FRONT OVER DOOR AND AROUND FRONT FRAME, LIFTED FRONT FACE OFF, FIRST CKD FUSE, BUT FUSE HAS A WHITE GLASS SO DIDNT KNOW IF IT WAS GOOD OR BAD, NEXT THING I SAW WAS THE HIGH VOLTAGE CAPACITOR, BUT CKD YOUR PRICES ON THE PARTS AND THEY WERE TWO OF THE CHEAPEST TO REPLACE, IT WAS REALLY GUESS WORK ON MY PART, SEE I USED TO WORK ON OVERHEARD CRANES IN A FACTORY, I LEARNED WHEN THEY OUIT WORKING IT WAS USALLY EITHER A FUSE OR A CAPACITOR, SO MY GUESS WORK WAS IN MY FAVOR, AND MY MICROWAVE CAME TO LIFE, I THANK YOU FOR THE NICE EMPLOYEES YOU HAVE WORKING AT PART SELECT FOR THEIR HELP AND GREAT SERVICE, DARRELL INGLE , HOUSTON TEXAS

Unplugged the microwave. I opened the door. I used a butter knife to pop the bezel off the inside of the door. I pushed the locker up and to the left and used the butter knife to pry it loose. Disconnected the locker from the spring, and reversed for the installation.

After checking all three switches for continuity I determined that the plastic door lever had warped or gone out of wack. After shutting off power at the breaker box I removed the door, the inside trim piece around the inside of the glass. Removed the black two prong door lever, reattached the new door lever and then reinstalled the trim piece and all screws. Works fine now. Easy fix just make sure your switches are all ok then replace the door lever.

Replaced entire door latch assembly with the three micro switches. Easier to replace entire latch assembly as individual switches do not remove easily from latch assembly. Had trouble removing front panel assembly. Parts ordered solved this problem.

Wanted to see the instructions before I install it.

Originally called it "grease filter" until I found very small print "air filter" on damaged original. Part #PS3527528

Slipped into place with ease -- right bottom of microwave

Change gasket

tested cap. with ohm meter which showed a short. A new HV cap., a fuse and it is working fine again.