Quick Question!

Have you ever purchased from PartSelect.com before?

Models > MHE14RFB0 > Instructions

MHE14RFB0 Roper Microwave - Instructions

All installation instructions for MHE14RFB0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the microwave repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the MHE14RFB0
31-45 of 187
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Bought a used microwave with no mount.

  • Customer: brady from Salt Lake City, UT
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 17 of 25 people found this instruction helpful
I found the part number for the mount on the appliances company website. Once I had that I visited a few sites looking for part. This site was easy to use and priced right, so I ordered. A few days later the product arrived as promised and worked perfectly for the install.

Wolud not heat or cook anything.

  • Customer: Wayne from Wingate, NC
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required:
  • 18 of 30 people found this instruction helpful
Instead of telling you, i have question do you have any instructions on how to do the repair. It would have helped save time on the repair.

This job took longer then it should have, becasue I did not start right in the begining. I did figure it out quickly after the wrong start.

You were a big help in picking the right part to correct the problem. You should be able to help with the repair. Thank You

The thing that makes the plate rotate was missing

  • Customer: Kim from MILTON, WV
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 10 of 13 people found this instruction helpful
I ordered the part according to the Model number, inserted the part very easily, (and I am soooo challenged in that area) and now it turns again. :)

Microwave Turntable Won't Rotate

  • Customer: Steven from Sacramento, CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 11 of 17 people found this instruction helpful
I turned off the power to the oven at the breaker. I then removed the side trim pieces by removing the screws located behind the lower oven door. I removed the plastic trim pieces above and below the microwave oven and removed the control panel and slid it into the opening above the microwave. I located the two screws securing the microwave into the frame and began sliding it out. I had to disconnect a small wiring harness and two wires from the microwave that were attached inside the opening above the microwave. The microwave section was the easily slid out, turned on it's side where the turntable motor was accessed by removing the access panel. I pulled the old motor, checked resistance and it matched the new motor. I then checked the old motor by applying 120V to it and it ran FINE! I thought I had the wrong part, but decided to install the new motor anyway. I did, secured the access panel and replaced the microwave in the frame. I reconnected the wires and secured the control panel and tested the microwave...and the turntable works!

Crack in front dress frame

  • Customer: Brian from Bixby, OK
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 6 of 8 people found this instruction helpful
Frame had cracked from a mounting screw hole and was unsightly
Assembled with new part but made sure that the screw was not overtightened

Needed to Replace the Front Vent Cover

  • Customer: MICHELE from ROSEVILLE, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 5 of 5 people found this instruction helpful
I didn't have to remove the old cover since it cracked and fell off the microwave already. I simply snapped in the new vent cover, screwed in the 2 screws and I was done. Super easy.

I broke the grill b/c I thought it snapped on and off, not.

  • Customer: Cynthia from Oceanside, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 5 of 6 people found this instruction helpful
I removed the two screws and took off the old grill. Snapped the new grill in place and replaced the screws. This model was not shown on the list but the part fit just fine. The part arrived in 2 days! I ordered the white one and at first didn't think it matched .. maybe my microwave was bisque or almond .. but after 15 minutes of scrubbing I realized it was white but just real dirty .. lol. Now the door opens without the grill falling off. Easy fix.

Existing tabs on plastic vent grill had broken off

  • Customer: Roland from Kissimmee, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 5 of 6 people found this instruction helpful
Removed screws holding the broken grill tabs with a phillips screwdriver
Removed broken grill and all broken tabs that fell into the vent area
Cleaned area where the new grill was to be placed
Inserted new grill onto the appropriate tabs and tightened the screws

BE CAREFUL as the tabs on the grill are thin and fragile when you insert the new grill don't force it into the slots, I used a knife as a way to slide the grill into place.

Stirrer cover had burn through

  • Customer: J.M. from SARASOTA, FL
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 5 of 6 people found this instruction helpful
the burn thru was probably because stirrer motor was not turning, Unplug the microwave .freed the motor up bu manually turning. temporary fix. The cover is held up with small push pin clips. Just pry the cover off with a screw driver or other flat tool. Scrape offf the old silicone. There are two covers in the Kit. you just need 1. Remove the old clips for the roof of the microwave, put a bead of silicone on the new cover where the old was and secure the new cover with the push pins into the clips .

Replacement of door handle

  • Customer: Denise from Hollywood Beach, FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 4 of 4 people found this instruction helpful
I made a video. There were specific instructions to note which needed to be explained. Interested?

Broken vent cover

  • Customer: Anthony from Robinson, IL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 5 of 7 people found this instruction helpful
Unscrewed the remaining pieces of bracket slipped in new vent cover and attached with the two screws. Very easy since the web site showed where the vent attached. I saved over $60.00 doing this repair myself!

Vent grille was broken

  • Customer: Eugene from Tampa, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 4 of 6 people found this instruction helpful
Removed the two screws hlolding the old vent in place. Discarded the old vent. Snapped the new vent in place and attached with the two screws previously removed.

bought microwave at Garage sale, but with no mount bracket

  • Customer: Jesus from Lincoln, NE
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 9 of 22 people found this instruction helpful
I was able to buy the mounting bracket for a very cheap price and was able to instill it in my kitchen with ease.
Thank you

glass turntable broke in half, ring turn needed replaced

  • Customer: Gail from Cincinnati, OH
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 3 of 4 people found this instruction helpful
I removed the broken tray and ring-turn and replaced it with the new
Service was fantastic, parts were ordered one day and received the next

The plastic screw brackets had broken on the original model.

  • Customer: James from Battle Ground, WA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 2 people found this instruction helpful
Removed the old vent grill by removing the two screws and put in the new one.
All Instructions for the MHE14RFB0
31-45 of 187