Quick Question!

Have you ever purchased from PartSelect.com before?

Models > MGR5775QDW > Instructions

MGR5775QDW Maytag Range - Instructions

All installation instructions for MGR5775QDW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the MGR5775QDW
241-255 of 316
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Oven Starter glows but oven does not get hot

  • Customer: Jim from Seaside, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Hello,

Your website and prediction that this replacement part was the problem were exactly correct. This part was easy to remove and replace, it is the starter for the oven so it comes with a heating element and a built in connector. I simply pulled the old wires up, unhooked the connector and removed the two mounting screws. Plugged in the new part, pushed the connector back down past the insulation, re-installed the screws and turned the oven on and poof, it started up again. We have also noticed that the oven stays hotter now, just like it did when we bought it.

Thank you very much for the advice and for supplying the correct part. A $65 part is much better than having to buy a $500 new stove/oven. We are very happy we found you and will use you again should some other appliance break down.

Sincerely,
Jim Arao
Seaside, CA 93955

Light lens broke when self clean cycle was used

  • Customer: James from Buford, GA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I searched Whirlpool, Sears and random appliance stores and Part Select was the only company to have the lens available. All other manufacturers said the lens was no longer manufactured as a stand alone piece and I would have to buy the entire light assembly. Thank you Parts Select!!!!!

Bake not coming on. Gas smell in oven when on bake mode.

  • Customer: Hector from Chandler, AZ
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Replaced the igniter as I've done with other products with similar problems. My amp tester wasn't working so I didn't test the igniter. The igniter wasn't the problem so I contacted a repair man who came up with the conclusion that the problem was actually the gas control valve. The valve wasn't letting enough gas to ignite the burner.

F2 error code, beeping, and oven wouldn't light

  • Customer: Michael from Hartland, WI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I had to pull the range out from the wall and loosen the rear cover to free the connector for the sensor as it got stuck on a corner guide. Put the new sensor in, rear cover back on, range back in place and tested the oven. Oven heats fast now and keeps a more even temp. Makes me wonder how long I was trying to cook with a bad sensor.

Light burned out in upper oven

  • Customer: Shirley from Las Vegas, NV
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Screwed in light bulb and glass protector

Oven would not turn on

  • Customer: Dave from Nashua, NH
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Replaced igniter, removed inside bottom cover 2 screws,removed igniter 2 screws & unplugged igniter from back of oven after removing plate with 1 screw. Could not have been any easier took less than 10 minutes. And doing business with PartSelect was great, would recommend and use again any chance I get.

F3 Code flashing and oven not working

  • Customer: Valerie from Bedford, TX
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I have and in the wall Magic Chef oven CGW3330ADW seriel 10799876US that came the purchase of my home 10yrs. ago. After a black out and 2 brown outs my oven would not start and the F3 code is beeping and the "door lock" light was on but the door was unlocked. The clock was working fine, but could not use the timer or set the temperature. I googled "FLASHING F3 code" and one of the results was the comment thread on the Parts Select website. When I clicked the link I read several customers sharing their story that was very similar to mine. I was able to click on a video and see a short demonstration on "HOW EASY" it was to replace the "Short Oven Sensor Kit." I though, "Yea right!" I left a comment on that You Tube video with my make and model and a brief explanation of my problem. I received a reply to my comment with in 24 hours, confirming what other consumers had shared...The "Short Oven Sensor Kit" was needing to be replaced. I ordered the part for around $30 VERY late on Thursday evening and when I woke on Friday morning, I a shipping confirmation email. I received it VERY early on Saturday morning! I was able to replace the part very easily with in about 10 minutes. I was VERY LUCKY that I was able to to the repair WITHOUT having to remove the oven for the wall! I would have had to pay for help if I had to remove it from the wall. The Parts Select web site save me over $400 which was the estimate for the parts and labor from a local appliance repair business! I was told that it would probably be cheaper or about the same as buying a new over which was their recommendation. I am so glad that I decided to do the research and in less that 1 hour I had my order placed. Thank You Parts Select!

oven wouldn't light sometimes, smelled gas

  • Customer: griff from gonzales, LA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
removed two screws from ignitor, pulled connector from hole behind it, replaced ignitor, reconnected. tried the oven and it worked first time. easy, easy.

Oven not heating.

  • Customer: Victor from Loxahatchee, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Removed the racks inside the oven then (2) screws that hold the bottom cover. Once the cover was off I exposed the burner element. I Removed (2) small Philips screws that held the unit. I removed electrical plug and the unit was out. I replaced the part and put everything back together. This was a very simple job took me about 10 minutes to complete. gas company wanted to charge $130 just to come out and look at. I saved some good cash.

Oven not lighting /

  • Customer: Jack from Benicia, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
removed oven door and shelves and lower pan and replaced igniter

Heat sensor went out causing oven to shut down.

  • Customer: Stephen from Metairie, LA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Cut off the electricity at the junction box. Removed two screws from the sensor at the back of the oven. Then pulled the sensor with the wire out of the installation hole in the back of the oven. Disconnected the quick connect plug from the sensor and reconnected the new part. Reversed the process and screwed the two screens back into the oven wall. Turned the electricity back on and started up the oven. (Everything ran well for about three days when the oven again signaled "F-5" indicating the oven was again not functioning properly. Restarted the oven and is currently running properly. My spouse does a lot of baking with this oven for cookies, roasts, etc. Next time it fails I will be forced to call a repairman as I believe there is something wrong other then the heat sensor.

oven would not heat up over 200

  • Customer: ricky from hollister, CA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
unplugged range took the oven racks out removed bottom plate, removed 2 screws from the igniter, wiggled the connector out of the hole, unplugged the connector. reconnected the connector reattached the igniter and put the plate and racks back in plugged the range in and it works just like it should. took about 15 mins. easier than I expected.

oven goes off like unplug no light no heat panel light come back on when oven get colder

  • Customer: boonsom from inglewood, CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
the repair was not difficult ,take time cause back panel has to be removed to gain access to unplug the temp sensor ,it appear to work but the digital clock still flash not all the timebut it should not flash , not sure that i have fixed it

Broken inner glass

  • Customer: Joe from Bronx, NY
  • Difficulty: Really Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Easy just loosened screws took apart door, removed broken glass and installed new glass.It took longer to clean the stove! Lol!

Gas smell and oven won't get hot, or takes too long.

  • Customer: Louis from Alpharetta, GA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I turned off the gas supply and unplugged the power source first. Then I removed the old igniter, by removing the plug wire clip from the back of the stove. I then removed the oven door by simply sliding it up and off the track. Once the oven door was removed I could easily access the igniter after removing the heat shield at the bottom of the stove. I had to remove two screws that mount the igniter. I had a little problem removing one screw, because it was stripped, so I had to use my Dremel tool to cut off the screw. Once it was removed the igniter was easily replaced with the new one. My wife and I was really excited that the fix worked! Saved me hundreds of dollars. Money I used for the holidays. Thanks Part Select!
All Instructions for the MGR5775QDW
241-255 of 316