MGC6430BDB Maytag Cooktop - Instructions

Open top oven door and remove the 2 front screws which hold the burners and controls to the frame. DO NOT lift the burners more than an inch or so to look inside. You WILL bend the gas lines in the back if you do. Pull out stove from the wall, shut off gas supply and disconnect hose if needed to have room to work. Remove top back panel and remove the 3 wires connecting the top burner assembly and also remove the 2 gas lines. Now you will be able to remove the burner assembly safely. Flip it over and try to unscrew the screw holding the igniter. When you fail, drill it out and get a small metal screw to replace it. The metal is soft and the screw is hard, so drill carefully. The rest is easy, put in the new igniter and screw. and put it back together.

remove small panel on right side of stove,then un clip moduke and put wires from old module to new one.
Exact fit nomproblems.

Having no manual nor finding any instructions online, I spent a while trying to figure out how to safely get to the ignitor mounting screw under the range top. I popped the snap clips on either side of the stove to loosen the top and pulled the top up a few inches to see why it was being difficult to raise. It turns out that the gas piping was solidly attached from the controls to the burners and I was slightly bending the tubes as the top was raised. The tubes have angles and curves to "accept" the bending pressure I was applying, so it looked like I was doing the right thing. In case I was not doing the right thing, however, I raised the top only enough to get access to the ignitor base and mounting screw. Then the fun began as the screw would not loosen. After several attempts using liquid wrench, tapping on it, etc., the screw head finally just broke off. Uh-ohhhh. Not to worry, however, as there was an empty mounting hole right next to the old one that appeared to be able to work. The mounting screw for the new ignitor was backordered, so I tried a couple dozen different screws I had in my toolkit and finally found one that would fit width-wise, but I had to nip off some of the length to get it to seat properly. The replacement ignitor also had a different width blade connector than the original so I had to grind away some of its width to reattach it to the lead wire. If I had a different sized blade receiver, I would have instead replaced the receiver on the end of the lead wire. It took about 90 minutes in all.

place new ones in by hand. the new ones fit too loose and if not carefull they will fall out.

Replaced spark module but same problem persisted. Realized that the insulation on the spark ignitors were all cracked, causing a short.

Lesson learned: check the condition of the spark ignitors first as these have a tendency to crack. Even the smallest crack will cause a short.

Ordered new spark ignitors and plan to complete repair.

3 of the 4 burner knobs were broken. Finding the burner knobs on PartsSelect.com. was easy. What sold me on purchasing them were the pictures including a closeup of the back connection and the description of the make of appliance they'd fit. I ordered them Friday and they arrived the next day (standard shipping) on Saturday. Pretty amazing since I'd been putting it off for 6 months.

Remove all 4 dripless pans; lift off the cooktop (from the base unit); remove and replace the switch / lead wire assembly; replace the cooktop and the dripless pans.

I removed all burners and lifted the top off. The system was two wires so simple to replace. I didn't know I could get the top off so easy. I first removed the fire box but couldn't see how to remove the top. I then realized that the burners mated the box and top. Easy fix since I had the right parts.

I simply took off the old knobs and replaced them with the new ones I ordered from you. They were exact replacements and cheaper than your competitors. You sent them quickly.
The experience can't be any better than that.
Frank

Shut off gas supply
Pulled stove away from wall removed spark ignigtor box .
Installed new one .
No problem.
Good for another 10 years

Piece of cake. Knobs were slip on / slip off. Searched the Partselect website using the model number of the cooktop... presto.

Removed grill and set aside, then removed burner with a 1/4 counter clock twist. Removed ground wire and igniter wire from burner. Set to side in order taken off. Remove the two screws on the panel that is on the back of the unit and slide it up and set it aside. Removed screws from side decorative panels each side (one top and one bottom) and slide panel toward the rear to remove from notch slot. Then removed the two screws on each side and back to remove top of range. On the side there are two screws together towards the rear, the one towards the front of the range need to be removed. Then removed four screws that held the pan under the range top that were screwed into the gas line supports. Then removed the two screws from rear that held the pan in place. Remove the pan and set aside. Lift the right gas line burner support up. Remove ground bottom, hot wires upper and igniter wires from spark module. Pop module out and replace with new one. Reverse process to complete repair. Cause that the wires do not get under the pan when reinstalling same

Removed old knobs and replaced with new knobs. Thank You

I ordered a full replacement for the five knobs so that the other four wouldn't look like they were dull due to being older. Took less than a minute to replace the items.

Simple as a dimple. Over time the plastic connections have gotten cracked or broken all together. Why they don't make them out of stainless is beyond me. Make more money, duh! Anyway, old off new ones one. Nothing else. This company speedy delivery - ordered Friday received Saturday. Thanks!