MGC5536BDS Maytag Cooktop Parts & Repair Help | PartSelect
Models > MGC5536BDS Maytag

MGC5536BDS Maytag Cooktop - Overview

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
(5)
PartSelect #:PS11744441
Manufacturer #:WP74011287
This is a burner knob and is used in conjunction with your range stove top. This knob accepts a D-shaped shaft. This part is black and gray with numbering indicating the various te...
$17.68
In Stock
(5)
PartSelect #:PS11770098
Manufacturer #:W10919249
$9.40
In Stock
(1)
PartSelect #:PS11742240
Manufacturer #:WP400021-1
Sold individually.
$8.16
In Stock
(2)
PartSelect #:PS11746840
Manufacturer #:WP90767
This screw is sold individually.
$7.76
In Stock
(7)
PartSelect #:PS11746068
Manufacturer #:WP8523793
This part helps your burner ignite and produce flame.
$25.74
In Stock
(9)
PartSelect #:PS2003170
Manufacturer #:12001596
This part may differ in appearance, but functions same as original part. : This part sends enough current to the igniter to create a spark to the bottom of the burner cap.
$64.03
In Stock
(2)
PartSelect #:PS11745641
Manufacturer #:WP8284669
Burner Cap - 6000 BTU Sold individually.
$34.71
In Stock
(2)
PartSelect #:PS11744194
Manufacturer #:WP74007705
This part is the replacement grommet for your cooktop or range. It is made of black plastic and is approximately 1 ¼ inches in diameter. This part may also be known as the cooktop ...
$8.63
In Stock
PartSelect #:PS11744195
Manufacturer #:WP74007749
$46.35
In Stock
PartSelect #:PS11744205
Manufacturer #:WP74007806
$95.10
In Stock
Questions and Answers for MGC5536BDS
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

top burners on stove won't ignite ,no clicking noise

  • Customer: scott from centreville, VA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 46 of 67 people found this instruction helpful
remove small panel on right side of stove,then un clip moduke and put wires from old module to new one.
Exact fit nomproblems. read more

spark igniter was weak and not lighting the flame.

  • Customer: Daniel from Needham, MA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Wrench (Adjustable), Wrench set
  • 33 of 44 people found this instruction helpful
Open top oven door and remove the 2 front screws which hold the burners and controls to the frame. DO NOT lift the burners more than an inch or so to look inside. You WILL bend the gas lines in the back if you do. Pull out stove from the wall, shut off gas supply and disconnect hose if needed to have room to work. Remove top back panel and remove the 3 wires... read more

No spark at top burners, first one then eventually all 4.

  • Customer: jonathan from Bryson City, NC
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 28 of 33 people found this instruction helpful
Most of the repair time was spent researching the problem online, locating the spark module inside the range, and selecting the part online. Installation was easy. Key troubleshooting info for me was, if there is no clicking, the spark unit is probably worn-out. I traced the ignition wires from the burners down to the spark module, located inside a 2x3" meta... read more