All Installation Instructions for Maytag Cooktop MGC5430ADW

Lost on of the Rubber Grommet holding the stove grate

So simple would be embarrassed to give any instructions; it is so self evident.

Parts Used:

Rubber Grommet

Martin from Millersburg, MI
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Thank you for voting!

Burner igniter was not lighting the pilot. Needed replacement.

We replaced 3 of 4 igniters on the stove top according to the previously submitted recommendations. Easy to do butt after putting one of the modules back together, we found one igniter still didn't function. We discovered the solution was to run the connecting wire under the gas tubing. Apparently it was compressed when it was over the top of the tube and not under it.

Parts Used:

Top Burner Igniter

Arthur from South Burlington, VT
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Thank you for voting!

Old burner's flame was coming out below the burner.

1/4 turn counter clockwise to remove the old burner, removed wires. Placed wires on new burner tightened them with pliers,dropped it in, 1/4 turn clockwise--done!

Parts Used:

Sealed Burner Cap with Electrode

Wayne from Midwest City, OK
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers

Was this instruction helpful to you?

Thank you for voting!

Wore out burner and igniter

New burner and igniter.....actually it was very easy to to fix

Parts Used:

Top Burner Igniter

Bruce from Vashon, WA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Thank you for voting!

Replacement of top burner igniter

Twisted and lifted off the burner, loosened in a previous repair; removed electrical wires from igniter; undid two screws holding igniter in place; rotated igniter 90 degrees and lifted it out; reversed process with new igniter.3

Parts Used:

Top Burner Igniter

Godfrey from Las Cruces, NM
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Thank you for voting!

burner rusted flames coming out the side of the burner

turned the old burner to the left and lifted it out. unpluged the wires with a screwdriver pluged the wires into the new burner and putit back on the stove and turned it to the right

Parts Used:

Sealed Burner Cap with Electrode

Lewis from Tomahawk, KY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Thank you for voting!

repair range burner

in and out in 15 min ,is easy when part fit.

Parts Used:

Sealed Burner Cap with Electrode

ZHENG from PINOLE, CA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers

Was this instruction helpful to you?

Thank you for voting!

Bottm Of Burner Rusted Out

Took my right hand twisted burner off unplug wires pluged them back into new burner and put burner back on done 3 mins tops.

Parts Used:

Sealed Burner Cap with Electrode

Paul from Oxford, MA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Thank you for voting!

Burners won't light up

We received the burners we ordered in timely manner, and it was very easy to install. Just unhook the old burners and drop the new ones in and connect.

Parts Used:

Sealed Burner Cap with Electrode

Bhavni from Richmond, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers

Was this instruction helpful to you?

Thank you for voting!

burners wouldn't light

First, only replaced the electrodes for lighting the stove burners. Nope, that wasn't the problem. Then replaced the burners -- that was the problem. Easy fix -- to bad I had to buy the electrodes first. Parts came in just a couple of days. Really surprised about how fast the parts shipped.

Parts Used:

Burner Head with Electrode

Daryl from San Pedro, CA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers

Was this instruction helpful to you?

Thank you for voting!

Igniter not working

Removed old igniter. Porcelain was broken. Replaced with new igniters. Really simple to do. Took 10 minutes to replace all 4

Parts Used:

Top Burner Igniter

Casey from Soledad, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Thank you for voting!

Flame coming from under burner cap

Unplug power, put strap wrench around burner cap and turn counter clockwise 1/4 turn, remove 2 wires, installed in reverse.took less than 5 minutes.

Parts Used:

Sealed Burner Cap with Electrode

Tom from Fenton, MI
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Thank you for voting!

No ignition of gas stove burner

Ordered the part, removed the wires (by light pulling) from the old burner and inserted them in the new one. Tried it, and it worked. Total work time, about 5 min. Amount saved, $150.

Parts Used:

Sealed Burner Cap with Electrode

Andrew from San Francisco, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Thank you for voting!

Bought a house with all 4 Burner grates missing

This isnt about repair, but about partselect.com. Best price on the interenet and very quick shipping. I got my order within two days of placing the order. I will use them again in the future.

Parts Used: