MFI2568AEW12 Maytag Refrigerator - Instructions

removed shelves, removed two hex screws re moved part then removed veggie draw slide,reversed process job done

Easily removed part. It took a bit more ingenuity to figure how to take off and reattach temp bar for salad drawer; but it is easily doable. I loved the company as they had the part to me in less than 2 days at a reasonable cost to repair the item.

Was really, really easy - wish I had done it months ago!! Removed the crisper drawers and then the glass shelf above the tray drawer. Took out drawer and then had to remove 3 screws to loosen the cap from the wall. Had a few small plastic pieces to take off (thermostat stuff), but all in all took about 10 minutes. Only reason I put down longer is that I cleaned up the whole inside of the fridge while I was there!

had to remove all drawers, once removed used nut driver to remove three screws. then removed the rail that holds the drawer. used nut driver again to remove rail from the original to mount the rail to the new bracket. Slide in holding brackets in front and back had to be removed, Then we had to do some wiping down and cleaning from spills that we had not seen. Installed the re-assembled bracket. installed the braces in front and back, installed the glass plate then re-installed the drawers. - took longer than I expected but worked fine.- weak point on the bracket is the pin that allows the door to pivot up/down.

Remove the drawers above the unit as others have indicated and the glass top and then using a 1/4 inch nut driver remove the screws. Now it gets just a bit tricky as the air control knob under the top is a two peice linkage that is best removed as a single unit being carefull not to break off the tab that rests in the middle back of the refrig. Simply swing it out towards the left as you face it and it will become obvious its just a simple tab and once it clears everything comes out in one unit. The logic holding everything together is simply a matter of squeezing a couple of tabs to remove the back portion then a couple more for the inner right side. Re assemble in reverse order and take the opportunity to give everything a real good cleaning. My time of about 45 minutes included a real good cleaning of all shelves etc....happy new year and thanks parts select for getting the part to me in what i think was next day...Awesome service guys

Simple- I removed the food, drawers, and shelving from the unit. I unscrewed the 2 screws holding the end cap on. Once removed I also separated the sliding track from the old part and put it on the new part. I then screwed the new end cap into place using the same screws as the old one. I put the shelves, drawers, and the food back in. All in less than 10 minutes.

Poped ou the old switch, connected new switch and pushed back into socket.

Remove drawers. Remove 1/4 screws. Remove end cap. The linkage for temp control is very fragile so be very careful. Not a very dificult task at all.

remove the two screws that hold the end cap on and carefully disassemble the linkage rods that control the temp control off and then just reverse the what you did. It wasn't that hard at all. The parts came in two days which was great. The bottom of the refrigerator needed to cleaned so it all worked out.

very easy

I pulled down the wire around the glass cover. . . Released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.

My wife said it was the wrong part before I opened the package. I took out what was in the way and put in what was in the package and everybody is happy. Dat's Dat from da Who Dat Nation!

Ordering the part was easy. Part came in a few days. I was able to install the part in a little over 15 minutes. Used a 1/4 inch nut driver. Three screws . Done! Happy wife!

Shut off water supply. filter is located in the upper right hand corner of the refrigerator on the inside. open the drop-down door. by hand pull the filter downward. then twist it to the left one quarter turn. it should pull out. I replaced it with a filter bypass plug. you can purchase a high quality filter to replace.it don't buy cheap filter.I made that mistake! hope this helps good luck!

Screwed in light bulb and glass protector