MFI2568AEW Maytag Refrigerator - Instructions

remove old replace with new part easy as that no brainer

After removing the glass shelf I simply removed the broken center rail and popped in the new one. It took only a couple of minutes from start to finish.

Ordered parts. They were here in 1 day. Followed directions on internet. Crisper slider took 10 seconds to replace after removing crispers and cover glass. The pantry end cap was replaced exactly as shown on the web site and took less than 5 minutes. Be careful putting cover back on the end cap because you do not want to snap the nib again.

Pins holding the door in place are part of the plastic end cap on either side of pantry drawer. Very easy to replace. Need only to remove two bolts holding the broken end cap in place, remove the drawer slide from that piece by removing two more bolts, reinstalling the drawer slide on the replacement end cap, and reinstalling the new end cap. Part was surprisingly cheap and arrived much sooner than indicated.

I actually hired a handyman who easily performed the repair

Removed crisper drawers, removed glass shelf and deli drawer and cover. Remove screws holding the sliding attachment and pantry end. After taking the old pantry end off I noticed that there was a plastic insert that went from the front to the rear, made a 90 degree turn and went to the rear area of the unit and was used to control the temp in the deli drawer. Took a little while to figure out how it worked and finally put it all together and reversed all of the steps taken to replace everything. Once I figured out the temp control slide it was easy to get it back together.

Looked at questions, picked one that applied, ordered suggested part, fix was super easy after watching video, Frig in running, part fixed it. Very excited, Thankyou.

Unscrewed the old filter and screwed in the new one

One mnorning the temp on the frig was in the 50's and the freezer was cold. Tried to get someone to come out and repair with no luck. We purchased a new frig. Then I decided to see if I could repair the old one to use. I wish I had discovered partselect before I bought the new one. First I thought from the web site that it was a overload/relay problem so I ordered it and changed it out and it was very easy. Then that did not correct the problem so I checked further and discovered that it could be the defrost heat element and thermostat. On partselect web site I saw where if your coil is covered in ice that this could be the reason. I ordered them and watched the video of how to change them out. The video is a little misleading because chances are you will not have the room around the coil that it shows on the video and also the element and thermostat will not come as one unit as shown on the video. It is still easy to cut the wires ont he thermostat and install it. The heat element is a little tricky to get out and back in and the clips that holds yours might be a little different and more difficult to do than the video but you can do it. All in all I spent about 160. 00 And the frig is working like new.

Thanks to a very patient husband. He looked at the situation and methodically took the freezer drawer apart by trial and error and was able to replace the old shaft with the one we had ordered. We do not understand why this basic information is not in the manual or on the internet. It was relatively easy once we knew in what order to take the drawer apart.

I mistakenly ordered the wrong part the first time and it was too short. After calling and giving the model # they were able to order the correct part. Installing it was easy, it just dropped into place.

squeezed in the ends of the cover to insert the posts. It was very easy! But, be careful, don't over do it, line it up first!

installed new center rail part worked perfectly.

Removed the drawer. 2 Removed the crisper drawers. 3 Removed the glass shelf and metal supports for that 4 Removed the 2 screws that held the slide in place 5 Removed the 3 screws that held the end cap in place 6 Carefully removed the end cap and temperature regulator from the refrigerator 7 Carefully removed the drawer temperature regulator mechanism from the old slide. 8 Reversed the above instructions to replace everything.

Removed drawer and right side pantry end cap. Removed slide for drawer. Reattached slide to new pantry end cap. Reattached new pantry end cap. Replaced drawer. Very easy. Entire job less than 10 min.