MFI2568AEB12 Maytag Refrigerator - Instructions

I broke the left side end cap the holds the pantry door on.
I search the internet for the part and happened to run across part select. I order the part and received the part with in 3 business days. It took less than 30 minutes to replace the end cap.

The great reviews help me with my choice to order the part from part select. I will order parts from them again.

Thanks for helping me fix my fridge.

Reviewed replacement instructions video on your website. Just followed the easy instructions to pop out old cover and pop in new cover. I would not have tried to replace it myself had I not seen your video. Super easy.

Followed the YouTube video linked to the Compressor Start Device and Capacitor I purchased. The repair was just as easy as the technician in the video said it would be. Removed the back panel, remove the clamp, worked the Compressor Start Device and Capacitor off the electrical prongs and replace it with the new one. After I reassemble the refrigerator, it was fully operational. Very easy to do and only required a few tools.

This took 30 seconds. Lift out shelf glass, remove broken pieces, snap new part into place.

you need to take the deli drawer out, make sure your flat head screw driver is large enough for the head of the screw as screwing into the plastic is a bit difficult. Other than that there are 2 screws and its pretty easy.

take out two nut driver screws remove piece, take off track two philips head screws. transfer temp control rod, really easy then put track back on and install piece. probable took as long to remove the two veg crispers and glass top. this is a very easy fix. i did notice that the pin on the original was about 3/8 of an inch forward so flapper door did not quite line up and im sure caused the pin to snap off. the replacement part, the pin is exactly the same position as the other side. i believe the original was defective from the mfgr.

After removing the shelves and drawers to gain access to the End Cap unit. I removed the screws and detached the unit which was a little tricky without any actual drawing details. After removing the unit I had to undo the plastic temperature control arm without breaking same. I then transferred the shelve draw slide and reconnected the control arm assembly to the new End Cap unit . At that point it was a simple installation, the drawer works better then new. Note: I did find some loose packing material behind the End Cap assembly unit that might have caused the failure of the drawer and door mechanism during its original factory fabrication. Other than that the project was a complete success. Dick S.

Pulled the broken pantry door off, and snapped the new door in place. Vry simple.

Took off old cover 3 screws...removed metal track and 2 other plastic sliding bars for air flow..put on new cover and carefully put back deli cover on plastic pins..easy fix...lousy design by maytag again! Thanks to PartSelect easy and prompt service and delivery!

It was a very simple operation to replace the parts and required essentially no tools, just a small screwdriver to pry up a tab for removal of the chanel on the front edge of the frame. This chanel had to be removed from the old crisper frame and installed in the new one. In addition the crisper control" had to be popped out of the old frame and into the new frame. Most of my time was spent cleaning.

We ordered the part by phone at about 4pm on Monday, and it arrived via Fed Ex at 10:30am the next day. WOW. My husband fixed it in about 5 minutes. Removed the old mullion with a socket set thing and screwdriver. Unscrewed the screw, slid the mullion up, disconnected a wider that is inside. Then he lined up the top and bottom plastic parts, reconnected the new wire, slid the new mullion in place, and screwed it on.

There was little or almost nothing to change out the End Cap, two screws on the End Cap and two screws on slide. It took longer to removed and replace the two drawers and shelve than it did to replace the End Cap. The part I ordered was exactly what I needed.

Once I realized the High voltage Board was bad I ordered the new High voltage board from Parts Select, the part was in stock and was delivered to my house in two days, I opened the box, and the instructions were very clear how to install the new high voltage board and program the board with the code for my refrigerator. There are also videos on You Tube on how to program the code on the refrigerator in case you have difficulty. In all, the problem was fixed and the refrigerator was up and running. Thank You Parts Select.

take the old one out replace with new once - no instructions required, no tools needed

remove front grill. with pry bar and wooden block, elevate side with broken wheel and insert wooden block behind assemble from the exterior bottom. With roller wheel assemble lose from the wooden block remove front elevator screw from the front frame. next remove cotter pin with the pliers and pull assemble pin. next elevate assemble out. drill out axle on the crimp side insert from the hardware store one 5/16 x 21/2 bolt with nut and new wheel. reinsert assemble in the reverse order. Remove wooden block and adjust height of wheel. replace grill. job complete. good job