MFF312BFWB Frigidaire Range - Instructions

Unplugged the stove first !
Removed bake element ; (2 screws), looked OK,
measured with an Ohm meter, measured "open".
Also, removed rear cover (6-screws), wires not burnt. Ordered new element-rec'd next day! My wife installed it and replaced rear cover. Works great (oven!) and about $10 cheaper and quicker than from a local dealer!

I unplugged the damaged element and plugged in the new one. It took less trhan 30 seconds and the unit worked just fine.

Very simple. Removed oven rack that had melted residue on it and replaced it with the new one from your company. I want to tell you that the delivery service I received was just geat. Took less than 48 hours to arrive at my home from the time I placed the order on line. Keep up the good work and I will be happy to share my experience with those in need of you services. Thanks. Marilyn Kasson

It took me more time to find the right tool then to remove and replace the element. If I can do it anybody can do it. Removed two (2) screws with a nutdriver. Detached the element replaced with new element and replaced screws. Easy job!

Unplug the oven, remove oven racks, unscrew 2 screws at the base of oven bake element, pull the terminals off the wire bases, plug terminals back in, put screws back in place, plug in oven and test that it works...

I simply followed the instructions in your video. i shut down the power to the oven via the breaker panel, removed the two quarter inch screws with a nut driver, pulled out the old element exposing the two wire leads,disconnected one lead at a time and duct taped each lead to the oven wall,. Then removed the old element and replaced the new one in reverse order. Voila! It works great. This is the second element I replaced in this oven over the years. This site was prompt on shipping the new element (about 3 days since I ordered on a Sunday).. It was well packed and arrived on time and I even got an e-mail letting me know it arrived! How cool is that?! I've been a customer for a few years now and plan to be a "forever" customer. Thanks for saving the day! You ROCK!

I watched the video of the repair. It was very easy; removed 2 screws; disconnected 2 push-on tabs; removed the element; and then reversed the operation. Be sure to turn off the circuit breaker that powers the oven before you start the repair. Turn it back on when finished and test the oven.

Got the shipment. Took it out of the package. Set it into the stove top. Tested to see if it worked, It did. Turned it off and took my dog for a walk.
Great company. Makes it easy for me order.

just put in slot

Remove screws pull off wires and install new parts

Simply...2 hex head screws removed. Unplug old element...plug in new element...place 2 screws back into place...test

It's a simple project. Remove old element and replace it with new one. Access is easy. Only one tool needed. What impressed me was how fast the part got here, like the next day after I ordered it.

took out the old one, screwed in the new one. very easy.

Drank a beer, grabbed a screwdriver & tried to remove the two screws that held the element in place. The screws were old and when I turned them, they stripped instantly. This required another beer. Eventually I used pliers to grip the sides of the screws to remove and reinsrt them. When I finished the oven worked great, so I celebrated with another beer.

First thing I did was turn off power to the range at the circuit breaker. The repair was generally easy with the exception that 1 screw holding the broiler element support was "welded" into the oven ceiling. I stripped the screw trying to get it out. Fortunately, I had a special tool that allows one to grip the outer edge of the screw while turning it --- and that's how I got it apart. Once the broiler element support was off, I removed 2 screws holding the broiler element itself to the oven wall and carefully pulled the broiler element out from the oven wall and detached the wire clips connecting the wires to the broiler element. I reattached the clips onto the new element and installed the new element back into the oven wall. I then reattached the broiler element support using a another screw (because I decimated the original one). I then turned the circuit breaker back on and turned the broiler on. Woila. My broiler works again! Special thanks to the people at this site who were very helpful in seeing to it I got the correct broiler element. The original ordered broiler element was delivered to the wrong address. The folks at this site sent me another one. To make a long story short, they saw to it I got the correct part. I highly recommend this site based on my experience with them.