MER6772BAW Maytag Range - Instructions

Very simple, I pulled the switch out from the front, unplugged the 2 wires and pluggedin the new switch. Pushed the new switch back in place and I was done. I figure I saved a couple hundred bucks.

I had some confusion about the correct series number associated with my stove and called Partselect. They confirmed the part I was looking at was correct in less than 5 minutes. I then completed the order online. Even with standard shipping my order was processed immediately and I received the heating element the next day.

Turned off the breaker. Removed the two screws in the front holding the range top down. Loosened the screws holding the element in place while balancing the range top with my shoulder. Removed the wires from the older element one at a time and attached them to the new element. Put the new element in place and screwed back in place. If I had a little help with the range top I think I could have completed it in 5 minutes but I was at home alone and the other stories of doing this repair made it seem easy enough and it was.

I removed the two small screws, gently pulled the element outward, slid the wire connectors off the ends of the element legs and reversed the process to install the new one. THE ELEMENT STILL DOES NOT HEAT. There must be a bad switch or thermostat at the ON switch area. That will be checked out by a Repair man as soon as I can get a schedule from him.

SHUT OFF BREAKER FOR OVEN! pulled oven out to get at backside,removed 3 screws on back coverplate,removed 2 screws inside oven at sensor in top left corner of oven,disconnected plastic clip at back ,pulled old sensor through hole.replaced sensor with new in reverse order. 15minutes tops.

I unplugged the oven then, one element at a time, I removed the screws and pulled the connecter out of the sleeve. This was the hardest part as it is a tight fit. Then, reverse the order to replace the element. The upper elements were more work because of the brackets used to hold them in place. But this only took alittle more time to remove and replace each one. When I plugged the oven back in and turned it on everything worked great! Back to baking!

Unplugged the unit. Removed the back of the range and disconnected the top element connectors. Then removed the screws holding top element from inside the range. I did not remove the bottom rack so that my arm could rest on that rather than risk hitting the bottom element. Removed the top element and inserted new element. Placed the front bracket to hold element in place and tightend the two screws holding the element to the back of the range. Then reattached the connecting wires, replaced the back panel. Then completed attaching the braces holding element to top of range. Did not tighten braces until all screws had been started.

1)Turn off breaker to range
1.1)Disconnect the downdraft vent blower
2)Remove Range from Counter area (delicate procedure)
Caution do not stress (Lift with or pull on) the cook-top
3)Remove Ceramic cook-top from base (hidden fasteners-remove the vert trim at front of range - it hides two fasteners)
4)Remove old elements
5)Rebuild the supplied elements (multiple options, copy the old element layout before disassembling- tricky)
6)Swap-out replacement elements (replacement elements were assembled slightly differently in the new style elements so wiring was slightly different)
7)Re-assemble Ceramic cook-top
8)Re-mount to base (needs assistant to support ceramic while reconnecting cable harness connector)
8) Re-set range into counter (Ceramic cook-top is very delicate, so extreme care is required to prevent damage)

Make sure you unplug your stove before you start! You should probably shut off the power at the breaker box too.

Since the upper oven is so small, I found that I couldn't reach the connectors well enough to work with them. So I pulled out the whole oven, took the screws off the back cover and from the back I was able to easily reach where the wires connected to the element. Then it was a piece of cake.

Just use a small knife to unbend the little metal things that hold on to the metal ends of the element. Slide them on to the new element, and crimp them tight with pliers.

Oh, you also have to take off the bracket on the ceiling of the inside of the oven to get the old element out, and the new one in.

The oven has been working great!

Shut off power to stove. Moved stove out. Loosened screws in top and middle back of stove and removed cover. Took mental note of color order of each wire and unhooked each wire from old switch and reattached to new switch in exact order of color of wire as original. Remounted cover on back of stove and reattached screws. Turned on power and turned on burner and tested burner for heat. Turned off burner, slid stove back and bingo - done. Saved a lot of money.

Repair would have only taken minutes, but upper support plate screws were rusted and almost fused to the plate. Once the plate screws were out (had to pry plate out) installation was done in 3-5 minutes.

As for the replacement part, worked perfect on the first try. Very happy with price, speed of delivery and preformance.

looked for how to video on you tube. It saved me lots of money. Anyone could do it.

Turned off breaker to oven, removed racks, unscrewed the plate holding the element in place, and pulled out the wires a few inches. All easy and fine to this point. Never having done anything like this before, I wasn't sure HOW the element was attached to the wires, so tugged on them a bit, but nothing budged. Got a flashlight (it got dark in there with the upper part of my body in there)looked again, but still couldn't tell. Referred to this site and saw reports of "plug and play", went back and examined the ends more closely on old and new element, realized that they slide straight on and straight off in a "sleeve". Got some pliars and pulled the ends apart. Slid the new end on to one wire, but couldn't get the other one on until I realized I had crushed it a bit with the pliars. Reopened the "sleeve" with a vegetable knife and slid the other end of the element into the "sleeve" at the end of the wire. Then pushed the wires back in and screwed plate on. It took about 23 minutes, and that included time to look up this site and do some reading, jump up to find a flashlight, and jump up and find a pair of pliars. My hubby was out of town for 3 weeks and suggested I wait til he got home--glad I didn't wait.

I had the old oven rack in the oven when I cleaned it. The rack came out brown and would not slide easily. The new rack was exactly the right one and now all is back to perfect!

needed to completely dis assemble the oven door to get to the inner pane of glass...took some time...I was able to do it on my own...could possibly go a little quicker with two people for a few of the steps...but possible by one...then reinserted the glass pane...and then need to re assemble the door layer by layer...up and working again...would have cost several hundred dollars if need to call a repair person in...this way was the cost of the piece..less than $70 ... and my time...well worth it....thanks

Had a technician from Home Advisor to check the problem out with my Whirlpool Double oven(1 1/2 old). Paid $60 to find the problem. According to the technician problem was control board and cost of labor and parts $465.00
Jumped on Part Select website, placed a question with my stove problem through the chat. Immediately they answered my question and told me the problem was the Terminal Block. Cost of part and shipping $25.00. Replaced it myself and everything works fine.
Thank you, Thank you Part Select for your help and honesty.

Sincerely
Peter from Maryland