Quick Question!

Have you ever purchased from PartSelect.com before?

Authentic Parts
Models > MER6770AAW

MER6770AAW Maytag Range - Overview

Get Parts and Repair Help for MER6770AAW

If you know the range repair part you need, you can browse the list of all parts on the MER6770AAW, or you can search by name or part description. You can also find your part by where it is located on the MER6770AAW by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your range. We’ve also included any installation videos we have for MER6770AAW parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Sections of the MER6770AAW

[Viewing 8 of 8]
BODY
CONTROL PANEL
DOOR (LOWER)
DOOR (UPPER)
OVEN
TOP ASSEMBLY
WIRING INFORMATION
WIRING INFORMATION
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$34.03
In Stock

Lower Bake Element

At the floor of the oven is the bake element. If your oven is electric, the bake element will likely provide 90 percent of the heat for baking. Therefore, the oven will not heat pr...

$29.74
In Stock

Long Oven Sensor

This long oven sensor is also commonly known as a temperature sensor. It is designed for use with ovens and ranges. It is similar to a thermostat; it measures and regulates the internal temperature of your oven cavity. There is an adapter at one end, a probe at the other, and they are connected by an insulated wire. The probe is approximately 7 inches long. You can test the sensor with a multi-meter for functionality. You need to check the model-specific manual to determine what the proper resistance is for your specific appliance. This oven sensor comes with two wire harness adapters and a set of instructions.

$2.96
In Stock

Screw

This is a multi-use and multi-appliance screw. It can be used on a microwave, refrigerator, range/oven, air conditioner, dehumidifier, washer, or dryer. The measurements of this sc...

$6.49
In Stock

Levelling Leg

This is a levelling leg for your oven, range, or stove. It is just under 3 inches long, is all black in colour, and is made entirely out of plastic. The levelling legs on your oven allow your appliance to sit perfectly flat. The new one may be longer in length than your original, but will work the same. Install the new leveling leg, and test if you have it adjusted properly by putting the appliance on four legs. Adjust in or out as required if your oven is rocking. It is recommended to check the other three levelling legs on your appliance in case they are also damaged or worn.

$42.18
In Stock

Broil Element - Push On Terminals

This broil element is found on the roof of the oven.

$44.96
In Stock

Door Gasket

The oven door gasket on your range functions as a seal between the warm interior of your oven, and the outside. It prevents heat from fleeing your oven when the door is closed. Before making any repairs to your oven you should make sure to wear work gloves to protect your hands, and give your oven time to cool. The only tool you will need to make this repair is a pair of needle nose pliers. This oven door gasket comes with built in retaining clips; if any retaining clips from your old gasket are left in the oven make sure to remove them before installing your new gasket.

$39.52
In Stock

Upper Bake Element - 240V

This bake element is found on the bottom of the oven.

$53.63
In Stock

Oven Rack

This is a replacement oven rack and it is designed for use with ranges and ovens. This is a genuine OEM replacement part. The rack provides a level and stable surface for cookware inside of your appliance. Installing the new rack is simple, you slide it into the pre-existing tracks in your oven. It measures approximately 23 inches wide by 16 inches deep. This replacement part is made of metal and it is sold individually.

$86.26
In Stock

6" Element with Limiter - 1200W

Sold individually.

$33.97
In Stock

Infinite Switch for Eight Inch Range Burner

This infinite switch is for 8-inch range burners. When an element is unable to produce any heat on a modern oven, the problem may lie with the infinite switch. This switch is responsible for sending power to the surface elements. Check the element and terminal block to ensure they are working properly. If they are in working order, check the infinite switch at the control panel for any wires that have overheated, or broken terminals to or from the infinite switch. If the infinite switch is damaged or malfunctioning, it will need to be replaced. Remember to unplug your range before beginning this repair.

Common Symptoms of the MER6770AAW

[Viewing 10 of 10]
Little to no heat when bak

Fixed by these parts

Show All
Element will not heat

Fixed by these parts

Show All
Oven not heating evenly

Fixed by these parts

Show All
Little to no heat when bro...

Fixed by these parts

Show All
Will Not Start

Fixed by these parts

Show All
Oven is too hot

Fixed by these parts

Show All
Touchpad does not respond

Fixed by these parts

Show All
Will not program

Fixed by these parts

Show All
Door won’t open after self...

Fixed by these parts

Show All
Door won’t close

Fixed by these parts

Show All

Replacing the Long Oven Sensor

Replacing the Levelling Leg

Replacing the Door Gasket

Replacing the Oven Rack

Replacing the 6" Element with Limiter - 1200W

Replacing the Infinite Switch for Eight Inch Range Burner

Replacing the Inner Door Glass Pane

Replacing the Infinite Switch - 6"

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Oven not holding 350 F, when cooling the coils did not reheat

  • Customer: David from Westford, MA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 122 of 141 people found this instruction helpful
Removed the oven door by opening slightly, then pic door up to remove. Remove 2 screws holding oven sensor in place, gently pull on sensor to remove, had to remove about 8 inches to get at plastic connector. Unplug connector, had to use an adapter cable supplied with the PartSelect kit to install new sensor, push cable back into opening, reinstall 2 screws. ... read more

Right rear burner went bad

  • Customer: Mark from Loxahatchee, FL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 115 of 128 people found this instruction helpful
Turned the breaker off, I removed 2 screws securing the range top to the range, opened the top and secured it in the up position, Removed the 2 screws securing the element ,one at a time I swapped the quick connectors from the old element to the new and repeated the process in reverse. I save over $100.00 in labor, plus most companies get you for a trip char... read more

Upper broiler element (of upper over) burnt out

  • Customer: Todd from San Antonio, TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 65 of 69 people found this instruction helpful
This particular model has a bracket that holds the element close to the oven ceiling, so I had to unscrew that as well as the element mounting screws on the back oven wall. The hardest part (not that hard) was the connectors were really tightly clamped to the element terminal. I had to use pliers to help wiggle them off the tips. Recommend doing this very... read more

All brand logos are trademarks of their respective owners.

The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.

Copyright © 1999-2017 , Eldis Group Partnership. All rights reserved.