MER5770AAW Maytag Range - Instructions

First I removed the two screws on the bottom heating element that hold the element in palace,one on the left side one on the right side, I then pulled the element out about 2 to 3 inches and disconnected the two wires. I then installed the new element. It took me about 20 mins. The cost of having some come out to fix this was about ten times of what I paid for this part. Thanks for the quick service.

disconnect power to range,took top off range turn upside down, remove screws holding element, disconnect wires to element and replace element with new element put every thing back as in reverse order and the range is working fine again.

First, I removed the two screws that hold the element in place. I then tried to pull the element out to disconnect the wires attached to the clips. The left side came right out. The right side would not. Had to pull the range out from the wall
(would only come out about a foot and a half due to the gas line connection). Removed the back (2 screws). Removed the clip from the element from the rear and redirected the wire into the oven. Replaced the back, pushed the oven back, attached the wire clip and screwed the element in place. Works fine. This is definitely a job not requiring an electrician.

The ceramic top of our stove got cracked last month. We went shopping for a new stove and we didn't want to spend $600+ on a replacement stove, as we really liked our Maytag. I got the part number off of the back of the stove and did a search on-line. I found PartsSelect.com and they had they exact cooktop for our stove for $259. I ordered it Friday afternoon and it was here Monday morning. It took me and my 8-year-old daughter about 15 minuutes to swap it out. There were only 4 screws and a wiring connector to swap and it was as good as new. I highly recommend PartsSelect.com for any appliance parts you may need!

Removed the large lower back panel of range (6-8 phillips screws) which holds upper control back panel in place. Removed upper control back panel (2 screws), exposing infinite switch electrical connections. At front face of control panel, removed (pulled off) control knob, exposing 2 phillips screws holding switch in place. (NOTE: A sleeve is on the switch arm or maybe remains inside the control knob). Look for this sleeve. Without it, the knob will NOT seize the switch rotary arm.
Removed each wire connection individually, one at a time, installing it in the proper position on the new switch.
Reverse all procedures to put things back together. A very simple, straight-forward operation.

Unplugged the stove and removed the back panel, disconnected the wires from the old receptacle, removed it, inserted the new receptacle, connected the wires, put the back panel of the stove on, plugged in the stove and then checked to see if the bulb was now burning. Success!

Removed the oven door and oven racks. Turned off the power to the range/oven. Unscrewed the bottom element and place the new element in its place. Screwed element in and replaced the oven door and racks. Turned the power back on and turned the oven on. It works great.

I removed the door, then removed the 5 screws holding the bottom and side trim on. I slid the trim down with the glass front. This exposed the screws holding the top trim on. I then removed the 8 screws holding the top on. At this point I took the opportunity to clean the three layers of glass. I then put the new handle onto the top trim, then installed it, then re-assembled the door and put it back on the stove. It took about 30 minutes including cleaning. Simple!

Removed 8 screws of retainer holding glass top to box.. Pulled 5 knobs and glass top and set aside. Popped 2 retaining clips holding burner , removed them and transferred to new burner (#12 and #48 position). Used wide blade screwdriver to facilitate removing terminals from old burner and attached terminals to new burner.Popped retaining clips into crossbeam, put glass top on and 8 screws back into retainer. Works great.

I didn't. Don't know how to get to light bulb to change it for this specific model

First I reviewed a video on YouTube by this site. Even though the range on the video was not the same as mind, it gave me an idea on what to do. I proceeded to pull the rang out from the wall and disconnected the power plug. Next I removed two screws from the back located on the left and used a flat blade screw driver to depress two brackets on the front to release the glass top panel. I unplugged the wiring harness and disconnected the grounding wire and took the glass panel off and laid it upside down on the kitchen table. I removed the old heating element first by unplugging the wiring and removing the brackets that held it in place. Installed the new one, plugged in all wirings, brackets, screws and replace the top back on the stove.

Repairman wanted $99 just to come look at it, then the cost to fix it. I got online, found the part, 2 screws and $40 later and all fixed. Wife baked me an apple pie that evening, better than ever!

Shut off power at breaker box , pull stove away from wall , remove Phillips screws from back of range pull knob off of switch . Look to see how switch is oriented remove 2 screws that hold switch in . Remove one set of wires at a time and place on new switch in same location . Put back together in reverse order .

I slide the range out and unplugged it from the outlet. I removed the back of the oven ( 8 screws ) using a cordless drill and phillips bit then with a phillips screwdriver I removed the oven sensor (2 screws) then I installed the new sensor , reinstalled the oven back , plugged the range in , slide it back into place and that was it. This repair took about 10 mins and the oven works perfectly. Thanks !

Turn off breaker in electric panel fore stove. Put screw driver into slots in front of glass top surface. Pry top up carefully until top pops up.Remove burner dial, remove two philips head screws holding switch. Lift top carefully and prop up.With new switch close remove wires from old switch one at a time and place on new switch. Place new switch back in place, securing with philips screws. Remove prop and carefully press top down until it snappes into place.Replace dial, turn breaker back on and try burner.