MER5755QAQ Maytag Range - Instructions

First I turned off the breaker for the oven. Next I pulled the oven out so I could access the back of the oven. Then I removed the back of the oven so that the connections for the heating element were exposed. I disconnected the wires from the element and then went back to the front of the oven. I removed the plate over the heating element (2 screws in the back) and then removed the screws that were holding the element in place. I pulled out the heating element and then put the new one in. Finally I hooked up the element to the electrical supply and then put everything back together. Don't forget to turn the breaker back on!

Purchased 2 piece broiler pan from this site

My wife called a service company and was told that a tech would have to inspect the stove.
service charge 60.00 After inspection the parts would be orderd and a 200 fee for labor plus the parts would be charged at the completeion of the job. 2 weeks for part. I found you on the net orderd the glass. got it in 2 days and I completed the repair in 20 mins. Cost 89.00

First we loosened the oven handle which required removing 4 screws. Then we removed the bottom piece which the glass sits on which required removing 5 screws. Placed the double stick tape on the frame then placed the glass on. We then put the bottom piece back on, tightned up the oven door handle and we were done. lrss than 1/2 hr later. This dose take 2 people to do otherwise you might drop and brake the glass. One thing I will say is that the oven glass did not come with the double sided tape to don't forget to order it. Also, there is only 1 piece of tape per package so order the proper amount your oven requires.

As the video described I just unscrewed the sensor from inside the oven. Although I couldn't pull the wiring harness through the insulation (the wires were gathered in back with a wire tie) just four screws to loosen the back panel for access to the connection. My wife says it seems to be heating perfectly now.

Removed the two screws holding the element in place. I then pulled the element and wiring out until I saw the connecter. I disconnected the two wires and then chose the correct connector from the package, snapped it back into place, put the screws back, turned on the breaker then tested the oven and found that everything was working correctly.
This is the second time I have ordered from Part Select, the first time was for a front LED panel on the same appliance. With the help finding the part you need and the comments from other customers I have saved a lot of money by repairing these problems myself. Oh, and the best part is the look on my husband's face when he came home and found out the repairs were made by me and not a repairman that he said I should call. He said he would laugh when the first repair by me didn't work but who's laughing now : )

I had a lot of trouble unlocking the door hindge you must pull the door out to change the hinge they are on the hinge and slide foward then pull the door up and out lay the door flat on a table cover the table with a towel so you don't scrach either one. Unscrew 6 screws on the door cover. 3 on top 3 on bottom take the cover off the hinges are exposed there 3 screws on the hinge 1 on the front and 2 on the bottom replace hinges install face insert door and lock the hinge it's all done. I wish I had these directions

I was told by appliance repairman that sensor and electronic panel were out - so ordered both as PartSelect was less expensive (about 1/2) than service call price. Sensor was in stock and arrived in 2 days, panel was special order from factory.
Replaced the sensor. Pressed Control Lock pad for several seconds and oven clock came on. Was able to set baking temp, broiler, and convection operation as normal.
Canceled order on panel as Sensor fixed my problem.

Turn off breaker.
Remove knob, pulls off. Pulled stove away from wall.
Removed front panel with switches attached.
There are screws in front and back.
Removed screws that hold switch in place.
Transferred wires one at at time to get proper location.
Reverse process for reassembly
Gary in Ohio

I removed the door from the oven and set it on towel on the table, and started the repair of the door. I removed the screws one at a time, and one layer at a time. Becareful you need to take the whole door apart, and remember how it goes bact together. In the end it was worth it. The hardest part was getting the right part. I thought I could order the whole door, and found out after several calls they don't sell the whole door. Part Select both times I put in my order had the parts at my door within 2 to 3 days. I also had to return one of the parts and within 2 to 3 days the part was credited to my account

I had some confusion about the correct series number associated with my stove and called Partselect. They confirmed the part I was looking at was correct in less than 5 minutes. I then completed the order online. Even with standard shipping my order was processed immediately and I received the heating element the next day.

Turned off the breaker. Removed the two screws in the front holding the range top down. Loosened the screws holding the element in place while balancing the range top with my shoulder. Removed the wires from the older element one at a time and attached them to the new element. Put the new element in place and screwed back in place. If I had a little help with the range top I think I could have completed it in 5 minutes but I was at home alone and the other stories of doing this repair made it seem easy enough and it was.

First I released the lock on the oven door hinge so that I could take the door off by lifting it up and out. Then it was just a matter of removing screws, replacing the hinges, and putting it back together. I did have to guess a little as I started removing screws as I wasn't sure exactly what to remove, but it became pretty self evident as I looked it over. Not as bad as I had expected.

SHUT OFF BREAKER FOR OVEN! pulled oven out to get at backside,removed 3 screws on back coverplate,removed 2 screws inside oven at sensor in top left corner of oven,disconnected plastic clip at back ,pulled old sensor through hole.replaced sensor with new in reverse order. 15minutes tops.

I screwed the light lens into the socket and went beautifully. Better than the original. (I am a retired, 75 yr. old woman).

looked for how to video on you tube. It saved me lots of money. Anyone could do it.