MER5730AAW Maytag Range - Instructions

I ordered both the light bulb and the switch that controls it. I had not pulled the stove out because the ones I bought this house from did not level the floor which meant I had to wait on a socket set to arrive in order to be able to pull my stove away from the wall. Once I got the socket set and the stove out I removed the panel on the back. I saw then that my red light bulb had shattered in half forcing the switch to just hang free. Glad I had ordered both parts, removed the old, replaced new with ease... then it was a matter of sliding the panel back in place without the main control panel getting misaligned, few trial and error checks and it went back with ease. New light works! Very easy.. probably less time if your floor is level.. then I had to play with the little legs to get it even again. For now it is ok until the spring where I go to redo the floor and make it all LEVEL! Very easy! Hope it doesn't burn out again but if it does I know what to do! Maytag rep wanted to charge me $100... No thanks!

Removed two screws holding cooktop to oven. Unlike the video, the cooktop was not detachable as the wires were hard-wired to the range, so I had to prop the top up with a 6" block of wood and was working upside down. I replaced the element and everything worked just fine.

Repair video was very helpful. I have removed the screws on both sides of the appliance under the surface plate, in the front. The Owen door has to be open for that. Then I have pulled the surface plate for a little space to disconnect the two connectors. Turned the surface plate over on the kitchen table, removed the 6 screws. Turned the burners assembly over and removed the small burner by disengaging the two clips. I have removed the 2 clops from the burned burner and assembled it to the new burner. I have placed the burner and engaged the 2 clips with a crownose players. I have removed one electrical connecter at a time and connected to the new burner. I have turned over the assembly over the glass plate and assembled the back cover with 6 screws. Put the surface plate on the range and connected the 2 connectors, pushed back, lined it up with the 2 screw holes in front of the range on bot sides and put the 2 screws in and Finished.

The repair would have been very easy, except this oven has a factory defect with wiring for the element on one side. The element should just plug in after removing 2 screw. The wiring on one side is too short to plug into the element without the assistance of something like a wrench with a bent long nose, hence the the surgical clamp. The seal, for cleaning, is really easy to replace, It just snaps in to designated holes.

Removed glass and then two screws to remove metal plate pulled out socket,disconnected two wires and installed new socket.

Disassembled upper unit with Phillips screwdriver. Removed 2 "plug connectors" from element switch. Replaced switch. Plugged both connectors back onto switch. Reassembled the upper portion of the range. Tested and OK

My husband did it within minutes. Very easy.

This job replacing the was so easy, it took about ten min,to do it thanks

The hardest part was deciding if this part would fix the problem. The upper oven became unusable. Both elements worked fine until reaching temperature. The oven would not come back on after that. I took two screws out. Then I pulled the wires out and unsnapped the coupling. The install was reverse. I just snapped the coupling in place and replaced the two screws. All works fine now. Saved a couple thousand as wife was prepared to buy a new one.

Our heating element ended up breaking from age and use. The repair was extremely easy: turn off breaker to oven, unscrew two screws holding in the heating element, pull it from the unit and detach the element from the electrical wiring. Once this is completed just perform the steps in reverse. The part arrived very quickly from PartSelect, arriving in just 2 days with the standard shipping. I am very pleased with my interaction with PartSelect.

Turn off power source before beginning.Unscrew the bracket attached to the back of the oven,carefully pull the heating element forward, exposing the connecting wires. Push any insulation back into wall while holding wires securely.Remove connection with needle nose pliers.Pull wires in wall from each side as far out as possible.Connect heating element to each wire carefully push back element lining up with holes in back of the oven. Attach screws snuggly and you're ready to use.

1. I ordered a replacement heater element from Parts Select, which arrived in just 3 days at my home. 2. I turned off the main circuit breaker to the range. 3. There are two small sheet metal screws inside the top left and right side of the oven door frame which need to be removed first in order to lift and remove the burner top from the range. 4. After lifting and pulling the burner top toward me about 6 inches, I unplugged the left and right burner assembly wiring harness connectors. 5. I lifted the burner top assembly off the stove and turned it upside down an a table. 6. There are six sheet metal screws that need to be removed to allow the sheet metal panel holding the heater assemblies to be lifted off and then also set upside down on a table top. All five burner elements are now visible. 7. Disconnect the slip-on electrical connectors to the specific heater assembly that is defective. 8. Unscrew the three small sheet metal screws from the three spring clips that support the heater assembly on the sheet metal panel; re-attach the spring clips to the new heater assembly. NOTE: Either memorize or record the position numbers that are cast into the ceramic housing of the burner to replace the new burner in exactly the same position. 9. Insert the three spring clips back into the sheet metal panel where the old, defective burner assembly had been removed. 10. Re-connect the slip-on wire clips to the new heater assembly in the same position as they were removed from the defective heater assembly. 11. Turn over the sheet metal panel with the burner assemblies attached and replace the sheet metal screws holding the panel to the stove top. 12. Turn over the stove top assembly and set back onto the range allowing space to reach to the back and re-connect the polarized connectors to the left and right side burners. 13. Slide the stove top back to the rear and carefully lower the front edge back down with the two metal tabs inserted back into the oven door frame. 14. Re-install the two sheet metal screws that hold down the stove top. 15. Turn on the main circuit breaker to the range. 16. Carefully test the new heater assembly by turning the range control knob to LO heat and watch for the stove top burner to momentarily turn red with heat. 17. Turn off the range control knob. 18. You are finished. It was a very easy installation.

There are five Phillips head screws to remove from the door (2 top, 3 bottom); the only touch part is that there are no screws on the sides, but instead plastic tabs on each side that "latch" inside the door frame; you have to use a flat blade screwdriver to work each tab and press on the door frame to unlatch each tab (yup I broke one, not knowing the setup the first time, but it went back together OK anyway). Once the tabs are unlatched from the frame, the entire front or the door will come off (be ready for this); then, just a few screws to take off the 2nd inner door glass frame (remove second glass carefully), and your to the inner glass, which just fits within the frame. Then, carefully backwards and the door is together again (once again, provide support as you take the last tab/screw off the outside of the front door, or you'll have more broken parts).

Remove sensor from oven. Disconnected wire from back. Connected new sensor and reinstalled. Temps now stay stable.

Watched the video and it was as easy as described. Not many things go as easily as this.