The drum support roller (Dryer Drum Support Roller, Drum Roller and Washer Assembly) holds the drum in the proper position while it spins on the support wheels. This part rotates on the roller shaft w...
$13.50
In Stock
Order within the next 8 hrs and your part ships today!
When the igniter reaches a high enough temperature, these coils (Coil Valve, Dryer Gas Valve Coil Kit, Dryer Valve Coil Kit, Gas Valve Solenoid) work together to open the gas valve and allow the gas t...
$30.89
In Stock
Order within the next 8 hrs and your part ships today!
The front glide is located at the front of the dryer, the drum rides along it. If you hear a metal-on-metal noise when your dryer is running, your front glide may be worn out and require replacing. Th...
$14.70
In Stock
Order within the next 8 hrs and your part ships today!
This roller shaft is also known as a support roller shaft or a drum roller axle, and is a part for your dryer. The function of this piece is to act as the axle for the drum roller; it provides a place...
$9.81
In Stock
Order within the next 8 hrs and your part ships today!
This multi rib belt spins the dryer drum during the drying cycle. This belt is 91-5/8 inches in length, 3/8th of an inch wide and has five ridges. It is black in color and made of rubber. You may need...
$28.37
In Stock
Order within the next 8 hrs and your part ships today!
This is a replacement lint filter for your dryer. The lint filter is approximately 12 1/2 inches in length. Simply remove the existing filter and replace it with the new one. Check for an excess build...
$44.63
In Stock
Order within the next 8 hrs and your part ships today!
This part is a retaining ring, sometimes called a retaining clip, that holds the drum support roller onto the shaft of a dryer. It is made entirely of metal and measures less than an inch in diameter....
$7.88
In Stock
Order within the next 8 hrs and your part ships today!
The idler pulley tightens the drive belt to properly spin the dryer drum. It is attached to an idler bracket. This part comes with the idler pulley and center bearing. To replace this part, you will n...
$22.11
In Stock
Order within the next 8 hrs and your part ships today!
If your gas dryer is not heating up or igniting, then replacing the flame sensor, located in the burner assembly, could solve it. This part senses heat from the igniter to monitor if it is hot enough ...
$47.91
In Stock
Order within the next 8 hrs and your part ships today!
If you notice that your dryer is noisy or will not tumble, then you may need to replace the drum roller shaft washer. This drum roller shaft washer is just under an inch in diameter and is sold indivi...
$13.79
In Stock
Order within the next 8 hrs and your part ships today!
This door catch kit is designed for use in dryers. This is an authentic OEM replacement part. This catch assembly ensures the door of your appliance will close, and remain closed. It allows your appli...
$32.34
In Stock
Order within the next 8 hrs and your part ships today!
Questions And Answers for MDG5500AWQ
Ask our experts a question about this model and we'll get back to you as soon as possible!
3 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Pablo
January 9, 2020
Drum spins ok with few clothing but slow when normal amount of clothing are put in
For model number MDG5500AWQ
Hello Pablo, Thank you for the question. I suggest checking the Belt PartSelect Number PS11741110 for wear. Sounds like it is worn and lose and not gripping the tub in order to tumble properly. We hope this helps!
Was this helpful?
Thank you for voting!
Sue
August 4, 2021
Dryer will not start after power surge.
For model number MDG5500AWQ
Hi Sue,
Thank you for your question. If your dryer will not start, there are some parts that you will need to check to see which one is causing the issue. You will need to check the door switch, the motor, the thermal fuse and the electronic control board. We hope this helps! Good luck with the repair!
Hi Lori, thank you for the question. The error DO means that your washer door is open. We would recommend closing the door properly and reset the unit by powering it off and turn it on back after 60 seconds. If the error persists, then you may need to replace the door switch, part number PS1964648, to fix the issue. We hope this helps, good luck with this repair!
PartSelect showed seven different possibilities why the dryer wouldn't heat. I removed the two screws to remove the bottom panel and turned the dryer on and noticed that the heating element that ignites the gas was working fine. This meant that it was not getting gas so it could be the gas valve or one of the two gas valve coils which are
... Read more located on top of the gas valve. I borrowed my neighbor"s ohm meter and touched the two probes on the coils terminals to check for continuity and found that one of the coils read zero. I then took both of the coils out by removing two screws and tested each coil again. One coil read 500-850 and the other read zero. This meant that it was no good so I called for the part and received it in three days. I reassembled the parts and turned the dryer on and it fired up after a few seconds. It works as good as new. The part plus shipping was less than $30. My repairman would have charged me $150-$200. While the dryer was apart I gave it a good cleaning with a vacuum and a toothbrush in delicate areas. I also removed and cleaned the lint trap housing by removing two nuts. I didn't know much about gas dryers, but thanks to PartSelect I easily fixed it myself.