MDE9700AYW Maytag Dryer - Instructions

Unplugged dryer from power source, used putty knife to release latches that hold top on, tilted the top out of the way, unplugged door lite, located the radiant switch, removed 1 screw,then undid 2 wires & lifted out switch. Reversed procedure plugged in dryer....wa la had dried a large load of clothes, took 1/3 the time to dry clothes at last. Thanks "PartSelect"

I verified that the thermistor was bad by testing the resistance. My manual said it should be 10K ohms at 78F. I was reading over 30K ohms. This is what caused the thermostat to blow, as the thermistor was telling the dryer the air temp was a good 30 degrees cooler than it actually was. You can also verify the thermostat is bad by checking it for continuity. I removed the screws on the top-back of the dryer and slid the top back to reveal the screws holding on the control panel. I removed those and popped off the control panel. It required a good bit of force. I then removed the four screws holding the front piece on and removed it by pulling it slightly towards me and up. The parts are located on the bottom right. They were underneath a black plastic flap on my dryer. I removed the cables and the took both parts out with a screwdriver. I replaced them with the new ones (they should only fit in the right slot) and reattached the cables. From there, reassemble in reverse of the disassembly.

Took the top back screws off (2) then pulled the top toward me and it came off. This left four screws that hold on the front control panel. I took out this four screws, which the control panel came out. You will then have to disconnect the door switch. Then I took off the front door, which which has two screws. Then I took the four screws out of the front panel,which are all on the top below the front control panel. You then have to pull up on the front panel to lift it up, it is sitting on two slots. This will give you excess to the heater. There will be one screw take it out and the heater will pull out also there will be six wires that you will have to disconnect so pay attention where they go (write it down.) You will have thermostat 2 and 3 and heater switch. Test them with a ohmmeter, my thermostat 3 was bad. There will be two screws to take out to replace the part. Put the wires back and put the dryer back together like you took it apart.

The kit gave me parts for two different styles of gas valve and told me what to look for to identify one from the other. Very easy conversion.

I feel like I have a new dryer now. I replace 3 of the 4 main components using parts select. Not only did they ship next day, but the tutorial videos with Steven were right on the money and self explanative.

I was working on my daughter’s Maytag dryer model MDE 9700 AYW. The dryer had been making a bumping sound for some time. It had the same symptoms a few years back, but it was still under warranty. The repairman had to replace a drum roller. He told her at the time he should replace all of them but he only had one with him. So when my daughter heard a similar sound she assumed it was a drum roller again so I ordered the roller without taking the dryer part. She has four boys that generate a lot of laundry, so she needs her dryer daily. I wasn’t sure how long it would take to get the part or do the repairs. The roller arrived very quickly, I think in a couple of days. The drum rollers on the dryer did not need to be replaced. What I found was bumping the side to the dryer because the sheet metal had popped inward. The drum has very little clearance on either side. The side probably could’ve used another crease or something to make it more rigid. My time wasn’t, wasted. I think it was will spent. I found that 3+ years of lint at piled up significantly on everything. The lint on the shroud for the heating coil had already turned brown and could have caused a fire. I would suggest to anyone who’s had a dryer for a while should open it up and vacuum out the lint buildup.
It only takes a Phillips screwdriver and very little time. It’s a very little investment for your peace of mind.

I change the Thermistor 3 bracket and worked well for 10 minutes and the thermistor is broken again

*Disconnect power cord before performing this task...(1) Remove the two screws holding top.(2) Remove four screws holding control module, tilt forward, pull up and unlatch. Place module on top, out of the way (still connected by wires). (3) Open dryer door, remove two screws holding lint trap assembly, close door. (4) Remove four screws on top of front cover, disconnect door light wire, tilt front cover forward, lift up from catch at bottom and remove. (5) Disconnect moisture sensor connection on bottom right for easier access to duct assembly. (6) Remove three screws holding duct assembly support bracket in place, raise duct assembly six inches to allow the bracket to be tilted toward rear and lifted out of the way. (7) Disconnect Red and Blue wires from front of duct assembly and pull assembly carefully from the rear of the unit and out the front paying attention to the wires still connected. (8) Remove wires connected to the thermostat and thermistor. (9) Remove screws holding in both units and replace with new components. (10) Reverse process and test. *note* if the unit appears to heat but clothing still wet, make sure moisture sensor was connected (I must have forgot and got to go back in to check, ooops). Regardless, this is an easy task. Could be intimidating at first but after the part has been accessed twice its no big deal and can be done over a lunch break.

Ordered thermal fuse and cycling thermostat