MDE9206AYW Maytag Dryer - Instructions

Shut off or unplugged dryer for safety.

Slipped thin blade putty knife up under bezel of switch to unlatch from the panel and pulled forward to remove the swwitch from the dryer. Unplugged the quick connect terminals (3) from the old switch and plugged them onto the new switch. one of the terminals had gotten quite hot and darkened the insulation so it was replaced with one that was supplied with the switch. that was a cut, strip, crimp process. Placed the new switch into the panel and snapped into place.

After reading all the other repair stories on Partselect, by the way thank you all, I removed the door, then removed the two security hooks that hold the top secure. Then I removed the front panel. I then marked all the screws on the outer door and shroud so I could easily put it back together. I left the all the wires connected and set the shroud and outer door to the side and removed the drum belt and drum. Removed the spring off the idler arm, then using nutdriver, removed the screw that secures the idler arm to the motor. Assembled the new idler arm parts and reversed the process to put it all back together. If I would have replaced the idler arm assembly the same time I replaced the drum support rollers, I wouldn't have had to do this twice! But now I am an expert repair tech on this particular model.

Removed front cover, removed old heating unit, installed new thermostat,heating coil inside the dryer and finally replaced the fuse in the front. The main complication was reaching the screws for the heating coil, not really complex.

remove bottom section under door 2 screws remove door 2 screws remove switch by squeezing tabs install 2 new female ends on wires supplied with switch . put switch back in plug in wires .

Ordered the part..... waited a few days fro it to arrive, (it came quite quick considering). Sat down in my easy chair and assembled the knob and gave it to my wife to slip it on the dryer. Whew, I was beat.... hehe

Took off door, then removed front of dryer to access the internal controls. Project went pretty darn well

took old one out then i had to strip the connector off new one was to big...

Replaced thermal fuse and replaced door switch

Knowing most mfgs. put prints under the conturo panal we started there.
Diagonstics required a multi meter.
The part was removed and the internet serched.
My local parts center was more expensive and would have to order the part. I called Partselect
found exactly what i needed. placed the order with 3 to 5 day ground. Fedex arived the next day. The new part was installed and the dryer smoke tested. The dryer works great.

I was able to easily find the replacement part on PartSelect, and the schematics showed me how to easily disassemble my dial (which has three parts) so that only the broken part needed to be replaced. I used a tiny straight-slot screwdriver to pop the pieces apart. Once we received the new piece, it was very simple to pop the pieces back together and have a fully functioning new dial!

It was very simple. I removed the fromt cover on the dryer. The heating element was easy to get to and after removing all the attached wires and 4 nuts. The new element was installed, reattached the wire correctly and put the screws back in place. It was extremely easy to complete.

If you are cursed with owning a Maytag product then you'll be glad PartSelet.com is in business. I get all my parts here.

My dryer motor burnt a phase. The tear down was very straight forward since there isn't much to a dryer. I did the tear down in the driveway. The dryer was full of lint so I blasted it with compressed air to clean it up. Keep all your parts in labeled baggies as you do the tear down. Reassembly goes much faster. The hardest part about changing the motor was getting the motor clips off. They are tough buggers. I used slip-joint pliers & finally popped them off. This job is simply enough for the average monkey. Just use the diagrams on partselect.com if you forget where something goes.

I shipped everything via fedex 2-day. It took 5 days to get here. partselect shipped it fast. fedex was the problem. I guess the boys at fedex have a public education is they think 5=2.

I used a flat screw driver to pop out the old female portion and snapped in the new one. Dryer stays shut. That's it!

Removed the door and machine front.replaced old duct assembly with new ,and reassembled front.

Press in the new female latch part with thumbs. Took about two seconds!