MDE4000AYW Maytag Dryer - Instructions

1 - unscrewed door
2 - made a mess because the directions did not work for my dryer
3 - figured it out = eventually
4 - popped loose the front panel
5 - unscrewed metal bars (that were holding the top down in the front)
6 - lift front like a hood on a car
7 - unscrew the rest of the front until the drum was loose and I could get to the felt strip
8 - glue new strip on where the old strip was = to the front and back plates that hold the drum
9 - put it back together :)

The replacement part just snapped into place. (The old part had fallen out) It took less than 30 seconds to do the repair.

removed dryer door 4 screws
removed front panel
removed front tumbler bracket
removed blower cover
removed wires attached to heat and door sensors
removed top
removed drum and belt
removed side panel
removed clamp holding idler pulley
replaced pulley and clamp
reversed above steps

First I put the square female end iof the door catch kit nto the square hole as snug as I could. Then I gently pushed the door against the piece until I heard it click in to place. That's it!! Sooooo simple--

Followed your video; replaced felt seal on front of drum, (torn in two or three places), and replaced both front guide kits,which were ground to the metal, causing the black dust, ( metal shavings). Thanks for the help, Buck. The drum support rollers were OK.

Okay, first of all, just let me say, if I can do this, ANYONE can. I am not very handy when it comes to things like this. I watched online videos and they will walk you through everything. I am so pleased with the results. Quiet as can be now. Before, we would have to shut the door when it was on because the scretching was so loud! The parts on this site were far more affordable than at my local repair store and they all came right to my doorstep. Overall it took me about 45 minutes and three beers :) Good luck!

Watch the video. Very, very easy

Took the door off the hinges. Removed remaining 6 screws and clips. removed the inner door. Made sure the door seal was correctly installed in the inner door. Installed the inner door and seal. Put the clips and screws back in. attached door to the hinges and was back in business.

I removed the 2 screws that hold the door and removed the door. I then removed all the screws that hold the front panel and removed the front panel. Then I was able to lift (on hinges) the top panel. I then removed the screws that hold the front drum housing, then removed the drum and belt. At that point you have plenty of room to access the idler pulley. I removed the Idler pulley spring. Then I removed the the screw holding the Idler arm and shaft. Reinstalled in reverse order.

Took off the front, took thd drum off, removed old belt, placed on new belt ptu everything back together.

Removed door and front and drum. Removed fan assembly. Be careful when working fan off of motor shaft. Unhooked wiring from motor. Removed clips. Replaced motor. Reverse procedure to put dryer back together. Now works like new. Very, very, happy. Part came in 2 days using standard shipping. Way better than buying a new dryer.

popped up top of dryer -- With pliers squeezed clips on inside of latch - - with screw driver pryed latch out -- just pused new latch in.......... Thanks to parts select for sending part sooo fast.. wife was happy.. Thanks, Dale

The dryer disassembly was pretty straightforward. The drive belt slips over the drum and easily prys over the drive and idler pulleys. The drum seal is held in place with the existing metal tabs. The old drum glides had to be drilled out and the new ones pop rivited in easily. Overall a rather simple process and the dryer sounds and drys like new again for minimal expenditure and time. Probably would have cost $200+ had I had a service person do the work.

Insure the double pole breaker in the breaker box is functioning properly.

I simply put the new lint filter in the spot for it inside the door.