Quick Question!

Have you ever purchased from PartSelect.com before?

Models > MDE3000AYW > Instructions

MDE3000AYW Maytag Dryer - Instructions

All installation instructions for MDE3000AYW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the MDE3000AYW
601-615 of 787
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

The door would not shut

  • Customer: Deborah from Worcester, MA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Pushed in the Door Catch, and it was fixed.

Noisy Dryer and then it stopped working

  • Customer: William R. from Seneca, SC
  • Difficulty: Really Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
Like all of us we have a lot of home projects on our plate. Our 10 year old Maytag cloth Dryer had been make noise all summer, but other project repairs where higher on the LIST. A week before the 4th of July the Dryer quit working. I should of made the repairs much sooner than I did. I had thought one or both of the Drum Rollers was sticking and making noise. It turned out one Roller had worn it's bronze bushing and the Shaft it ran on. The biggest problem was that the plastic Idler Pulley had stuck to it's Shaft and stopped turning. The Drum Multi-Rib Belt then had worn through the plastic Pulley destroying the Pulley and breaking the Belt. It was easier than I thought to get to the problems parts. I looked at videos from PartSelect.com and got some good pointers.I ordered the replacement parts from PartSelect.com and received them in 3 days! I had the Dryer back working within two hours after I received the parts and before the 4th of July. I would recommend if you do this repair, order the Multi-Rib Belt, at least one of the two Drum Support Rollers, both Roller Shaft, Idler Pulley Wheel and Bearing, and the Idler Arm with Shaft. For less than $95 I had the Dryer working like new.

Large gap at bottom of drum/door and tight at the top, allowing clothes to get wedged and damaged/marked

  • Customer: William from Santa Barbara, CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
As described on video, except re-installing the belt was difficult. I found it easier to reinstall the drum first, then put belt on inside the grooved part of the drum, so there is some slack. Once installed around the idler and drive shaft, slide the belt forward into final position

Lint filter had a hole in it.

  • Customer: David from Charlotte, NC
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
This repair was simple. I had ordered parts for my refrigerator on this web site and it also went perfect and I saved well over $200.00. The videos show you everything. Don't do anything until you look here first!!

Broken dryer timer knob

  • Customer: Stephen from Carmel, IN
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Very simple. Remove 3 piece assembly from metal spine by pulling it off. Disassemble by snapping apart the 3 pieces. Replace the broken skirt. Snap back together and slide onto the spine. Even ordering was easy using your website and the part arrived in 3 days. Great service. Thank you. I've already recommended you to several friends.

Baffle came off

  • Customer: Teddy from Boca Raton, FL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
followed the instructional video and it was very easy. Videos are great

Dryer was making a metal on metal grinding noise as the drum turned, but only through maybe 45* of its rotation.

  • Customer: Clarence from Howell, MI
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Removed the door, the front panel and the lint screen panel (easily done with a nut driver and a screw driver - 2 screws on the door and 8 screws for the panels). Tilted the top of the dryer open to see the drum. Turned the drum by hand and heard the same noise. Examined the felt pieces that insulate/isolate the drum from the front cover that retains and positions the drum. They were worn some, but intact. Noticed that one the the two front glide kits the the drum rides on (these are riveted to the bottom of the front panel mentioned above)was completely worn through allowing metal on metal contact. Ordered a new glide kit (about $20 including shipping - 3 days to arrive). Drilled out old rivets and removed what was left of the old glide kit. Installed new glide kit using the 2 rivets that came with the cork and 'teflon'? This took maybe 15 minutes. Reinstalled all covers and took it for a test run. No noise. Wife thinks I'm a hero!

No Power

  • Customer: John from Bel Air, MD
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
Installing the new switch was a snap. With the dryer unplugged, open the top using a putty knife to release the 2 clips - one on each side. Lift the top and support it to stay open. Next, note the wire color and location for each of the 3 wires. Remove each wire from its prong on the bad switch by gripping the connector with pliers and pulling off. Next remove the bad switch by squeezing the tabs on the sides of the switch to release it. The switch removes to the front of the dryer. Install the new switch in the same method and reconnect the wires as before making sure the colors go back on the same prongs. I had to replace one of the connectors with a larger one (that came with the switch) since one of the prongs on the new switch was larger than the orginal (bad) switch. To do this, I cut the old connector off, stripped the end of the wire, and crimpted on the new connector. I had to be careful not to waste too much wire since there was very little slack to work with.

Timer dial skirt broke

  • Customer: Irene from Springfield, MA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Snapped pieces together, aligned skirt notch with notch on machine, pushed on. Repair done.

Noise when tumbler was rotating

  • Customer: Darrell from Weston, WV
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Actually I followed the installation instruction video provide by this website. Instruction videos are excellent for those of us that don't do this very often. Also, I would like to comment on how fast my part was delivered. I ordered it online one afternoon and it was at my door the very next morning.

Squeeky bearings

  • Customer: James from Gainesville, GA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Followed the videos associated with the parts. NOTE: two videos showed turning the belt smooth side toward the drum, one showed it ribs toward the drum. Important thing is to assure the ribs fit into the grooves on the motor pulley with no twists in the belt.

Broken knob

  • Customer: Andrea L from Issaquah, WA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Snapped pieces together and installed

Dial on dryer broke

  • Customer: Lloyd from Freehold, NJ
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
This was the most amazing repair. Got part quickly and took less than 5 min to repair and my wife is elated since using pliers to turn dial on dryer for over a year was no fun :-)

Door Latch broken

  • Customer: Eugene from Arlington, TX
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Ordered part ( door latch ) flowed instructions easily fixed same.

Rodent entered through vent, chewed through outlet duct assembly and vent screen

  • Customer: Donald from Danville, KY
  • Difficulty: Very Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
  • 0 of 0 people found this instruction helpful
Removed door. Removed screws from outlet duct assembly except for 2 hidden screws that were only accessible from inside the dryer between the drum and outer assembly. Had to pull back the felt between the two units to access the hidden screws. Used 1/8" welding rod to stabilize the outer drum unit so it wouldn't fall. Removed the hidden screws. Carefully found two screw receptacles and working only by feel, was able to install the two hidden screws. The rest of the assembly went smoothly, especially after marking where each screw went. Had to remove 3 wires from outer drum unit but marked them with letters signifying color and reinstalled easily. All in all, a very difficult job due to the two hidden internal screws. I would recommend a general handyman hire this job to a technician.
All Instructions for the MDE3000AYW
601-615 of 787