MDE14PNAYW Maytag Dryer - Instructions

took old one out then i had to strip the connector off new one was to big...

Removed front cover, removed old heating unit, installed new thermostat,heating coil inside the dryer and finally replaced the fuse in the front. The main complication was reaching the screws for the heating coil, not really complex.

Replaced thermal fuse and replaced door switch

Knowing most mfgs. put prints under the conturo panal we started there.
Diagonstics required a multi meter.
The part was removed and the internet serched.
My local parts center was more expensive and would have to order the part. I called Partselect
found exactly what i needed. placed the order with 3 to 5 day ground. Fedex arived the next day. The new part was installed and the dryer smoke tested. The dryer works great.

Dryer stopped heating after a few days of it being an intermintant problem. I ohmed the heating coil and it was fine @ 12-15 ohms and the 2 sensors were open so I knew they were not the problem. The only item left was the Heater Relay. As soon as it was changed, dryer operated as it should.

If you are cursed with owning a Maytag product then you'll be glad PartSelet.com is in business. I get all my parts here.

My dryer motor burnt a phase. The tear down was very straight forward since there isn't much to a dryer. I did the tear down in the driveway. The dryer was full of lint so I blasted it with compressed air to clean it up. Keep all your parts in labeled baggies as you do the tear down. Reassembly goes much faster. The hardest part about changing the motor was getting the motor clips off. They are tough buggers. I used slip-joint pliers & finally popped them off. This job is simply enough for the average monkey. Just use the diagrams on partselect.com if you forget where something goes.

I shipped everything via fedex 2-day. It took 5 days to get here. partselect shipped it fast. fedex was the problem. I guess the boys at fedex have a public education is they think 5=2.

It was very simple. I removed the fromt cover on the dryer. The heating element was easy to get to and after removing all the attached wires and 4 nuts. The new element was installed, reattached the wire correctly and put the screws back in place. It was extremely easy to complete.

A year or so ago I replaced one drum wheel. The dryer worked fine for months until it started sqeaking again. When I removed the wheels again the shaft was no longer round but half moon shaped. this allowed the drum to drop lower than it's supposed to. consequently the drum ate through the back drum support. I replaced the back drum support and the roller shafts, in addition to two new rollers. It works great now. The more difficult part of the repair was replacing the rear drum support. It is screwed in from the back and requires two people. Everything else I did by myself. The lesson: If you replace the rollers, be sure the roller shafts are not worn. An asymetric shaft eventually causes more parts to wear out.

I watched the video

Watch the video. Very, very easy

removed dryer door 4 screws
removed front panel
removed front tumbler bracket
removed blower cover
removed wires attached to heat and door sensors
removed top
removed drum and belt
removed side panel
removed clamp holding idler pulley
replaced pulley and clamp
reversed above steps

First I put the square female end iof the door catch kit nto the square hole as snug as I could. Then I gently pushed the door against the piece until I heard it click in to place. That's it!! Sooooo simple--

Took off the four screws to get to the female clip and used pliers to squeeze it out. Next was using pliers to pinch out the male connector and place the new one in.

1 - unscrewed door
2 - made a mess because the directions did not work for my dryer
3 - figured it out = eventually
4 - popped loose the front panel
5 - unscrewed metal bars (that were holding the top down in the front)
6 - lift front like a hood on a car
7 - unscrew the rest of the front until the drum was loose and I could get to the felt strip
8 - glue new strip on where the old strip was = to the front and back plates that hold the drum
9 - put it back together :)

The replacement part just snapped into place. (The old part had fallen out) It took less than 30 seconds to do the repair.