MDBTT59AWW Maytag Dishwasher - Instructions

Not a bad repair once you diagnose the problem. Took me three tries to figure it out. Just make sure you follow the instructions. I used an allen wrench to hold the motor in place while tightening the part onto the motor shaft, this way I didn't have to remove and flip the dishwasher to do the repair. The good news is the replacement part I needed was metal instead of plastic, thus I should never have this problem again. I don't understand why it was plastic in the first place but all of my appliance problems seem to be made to fail after several years of service.
Repair was

First I opened the breaker on the dishwasher removing power from the unit. Then I removed the Torx head screws on the cover on the back side of the front door. Then I pulled off the stainless steel sheet metal panel which exposed the door latch. Then I unplugged the electrical connectors to the two micro switches on the assembly, next I plugged in the connectors on the new latch assembly and postioned the latch back on the mounting holes. Replaced the stainless steel sheet metal and put the screws back.

I pulled the dishwasher out from under the countertop. It was quit easy to get to in the lower left front corner of the appliance. I loosened up the bracket that was holding the valve in place. Removed the wires, and taped and ID them so that I would know which one went where. Removed the hose clamp, pulled the hose off and removed the old valve. Put the new one back in just as I removed the old one in the same order. It was a snap! This is not the first time I have used PartSelect! Our evaporate fan went out on our refrigerator a couple years ago, replaced that. A shelf broke in our refrigerator twice, each one different at different times bought both from Part Select. This is the first place I look for help with repairs! I at least attempt to save money, then if it's too difficult I will hire a repairman. So Far, PartSelect has saved me a lot of money on doing it myself! Thanks PartSelect for making small repairs easy to tackle yourself, along with reasonable prices for parts!

First and foremost, turn off the power to the dishwasher at the breaker panel. Next, open the door and remove all of the Torx screws along the door edge, except the bottom two. The inner skin will open enough, and there is sufficient slack in the wires, to change out the latch assembly without completely removing the whole inner door skin. Next, remove the wire harness plug from the right switch and then insert it onto the right switch of the new assembly. Do the same with the wires for the left switch. Note, you may need a pair of pliers to remove the wire connector from the switches. Place the switch back in place, lining up the screw holes properly, and replace all of the Torx screws. Turn the breaker back on and you are done.

Not only could I get the part from PartSelect.com quicker than I could from Sears, the total cost with shipping was the same as Sears wanted for just he part!

There was a tear in the fine filter (fabric) on the accumulator. This can be seen by looking in dishwasher without having to disassemble anything. Food was being sucked in and sprayed back out on dishes.

Disassembled, cleaned, replaced part then reassembled.

Cleaned out the spinning sprayers -- used toothpicks to clean out holes, flushed with water.

Cleaned out under the accumulator.

Works like new.

The big problem is that you cannot purchase the wheels only. I found that out after ordering the rack track because that looked like what I needed. But it didn't come with the wheels. So I returned it. Then I went to the basement and found things in my junk boxes and fixed it without purchasing the complete parts. Cost: 10 cents for two nuts vs $60 for the required parts.

Peeled off the old foam strip, cleaned with rubbing alcohol, let dry completely, applied new foam strip,replaced door interior done I wish repairing relationships with fiance and kids were one tenth this easy.

First, I recommend asking PartSelect for help to insure you have correct part. They tell me the pictures on the web site are provided by Maytag and are copywrited so they can't change them. The pictures are incorrect and misleading. However, it's a known problem, so the PartSelect people will steer you in the right direction. Bottom line in my case, I needed the lower cost part that included more pieces (counter-intuitive so I was glad I called). Got the right part the first time in about 3 days regular shipping.

As far as install, you need a "Torx" screwdriver (screw heads have a star-like pattern) to remove the screws along the inside of the door. From there, the old latch is accessible and easy to remove. As others have mentioned, the hardest part is removing the wire harnesses on either side of the latch. They have a slide on compression clip holding them on, and I think that time and ambient moisture must cause them to get stuck very tightly. I originally thought there was something locking them on, but in the end, I was able to pull and wiggle them loose with by applying slight inward pressure on the prongs with long nose pliers. You have to be careful not to damage the parts when attempting to pull them apart. It's nice that the part I ordered includes new switches, so if I caused any damge removing the old ones, it didn't matter. Just take extra care on the side with the wires and plastic connectors, since those parts aren't included and are more involved to replace if you damage them.

Overall, a very simple repair. The repair stories from others on the site were very helpful and gave me confidence when I ran into the small snag mentioned, since others had the same problem. Hopefully the additional detail I've provided on that issue will help fill any gaps.

Simple. Unscrew the old one, replace with the new one.
The best part- Online said it would take 5-7 days to recieve thru the mail. It arrived the very next day!!!!

First turned off power to dishwasher. Then, I removed all the screws on the dishwasher door. Removed old plastic door latch from wire assembly piece. Pressed on latches for square small wire boxes connected to wire assembly piece to be able to handle wire assembly plastic piece without attachment to dishwasher. Tried to snap door handle to wire assembly plastic piece, but didn't seem to fit - was too tight. Checked for discussion online and found that it required heavy pressure to snap in place. Used pliers to clamp down on outer plastic on wire assembly piece to squeeze fit door latch plastic hooks in place. This was difficult, but with heavy pressure finally managed to snap in outer hooks. Then with difficulty snapped in inner hooks. Was afraid of breaking new plastic piece, but all worked out well. Door has never opened and closed so well!!

All i had to do was ....first unplug the dishwasher,then remove 10 of the Torx head screws on the inside of the door.(from the top down)
With that done i could open the cover without taking it off. then unplug the switches,and replace the new handle.
screw the cover back in place.
done! piece a cake!
MD
PS (don't forget to plug it back in)

after reading a article on problems the logic one was frist the door. Order the part ,took off the inter panel with star slot (10)exposed the handle and switch. Removed it, abit hard at frist,then replacement went in easy , the washer worked.
I guess I was lucky because on the other side of handle similar type of part thats maytag for you.

took screws our of side trim and top trim, decreased height on leveler legs and pulled dishwasher from the cabinet, replaced cables and springs from both sides on the door, lubed door hinges cleaned everything under dishwasher re-inserted and re-installed trim screws. took around an hour with clean up.

We followed the instructions in the video online to replace the latch assembly. Removing the electric wires from the old latch assembly was difficult; I read that others had trouble with that too. Two of us worked together. I inserted a screwdriver between the plastic box shaped thing holding the wires and the old latch assembly --- between the two metal pieces that extended from the latch into the plastic box shaped thing. I pushed the screwdriver thru until I could hold both ends. I held tightly while my partner pulled the latch assembly off of the wires. Repeat for the wires on the other side. Pretty easy. So happy to have fixed it ourselves.

First, we removed all of the screws around the perimeter of the interior door panel and lifted it up. (we didn't take it completely off because that would have required disconnecting wires so we just held it up out of the way.)

Second, the plastic on the latch assembly was broken so that part came out fairly easily. The hard part was disconnecting the metal prongs that plug it in to the door control wires. We tried everything--prying, pulling--and finally got all three of us in there. One pulled on the latch end of the prongs, the other pulled on the door wiring end of the prongs, and I squeezed the prongs in-between with needle nose pliers. This broke the prongs on the latch side, which was fine since we were replacing the entire latch (the directions in the service manual we downloaded didn't give any indication that disconnecting the prongs would be difficult--I feel like there must be a trick to it, but breaking the prongs worked fine too!)

Third, we plugged in the prongs of the new latch--went in easily!--and popped the new latch into place in the door. It wasn't held securely, probably because of the broken plastic, but we replaced the inner door and screwed it in place, and when we shut the door it worked.