MDBH955AWS Maytag Dishwasher - Instructions

This was a very easy repair. Before I did anything, I flipped the breaker for the dishwasher and tried to turn the dishwasher on to make sure it had no power going to it. Once I was certain the power was off I removed the hex screws (there are 11) on the inside of the door panel using the hex screwdriver. Lifting and holding the inside panel up, I then used the pliers to pry the old latch assembly out of its metal prongs. Then I replaced the old latch assembly with the new one, pushing the metal prongs (by hand) into the slits of the new latch assembly. Last, I lined everything up and screwed the door panel back in place. I flipped the breaker back on and activated my child lock to make sure I had power. The handle worked perfectly. Quick and easy fix!
I ordered the part with 3-5 day delivery and actually received it in 2 days! I'm extremely pleased with my partselect.com experience and highly recommend using them for all your appliance parts needs!

i ordered the parts on sunday night at about 9pm. the parts arrived on tuesday afternoon! i removed the screws on the inside of the door, then removed the latch assembly and unplugged the two connectors. i then plugged in the new latch assembly and replaced the screws. i accidentally ordered two parts i did not need and received an email twenty minutes after i asked how to return the unneeded parts descibing the return process. i have already told three people how awesome your company is. anytime i need appliance parts i won't look anywhere else. you have a customer for life!! thanks for everything.

I could not reach the heater element nuts from under the dishwasher so had to pull out the dishwasher. I removed the screws around the front of the dishwasher and pulled it about half way out before the water inlet pipe and the electrical wires stopped me. I shut off the water, unhooked the copper pipe, and unhooked the electrical wires (shut off circuit breaker first). Pulled the dishwaser out so I could remove the element nuts and wires to the element. Removed the old element and installed the new one - the old nuts would not fit. I went to a local appliance parts store and found that my element is no longer made. I had the correct replacement element but you need to order the nuts also. Luckily, the local store had a small brass nut that worked. Reattached the electrical wires to the element, pushed the dishwasher half way in, reattached the water inlet and electrical wires, pushed the dishwasher all the way in and scewed back into the cabinets. All is well now and the dishwasher is working much better.

Door gasket was easy out and in using the white mark on the seal to line it up with the center. The latch came with the handle so I returned the extra latch assembly that I ordered. Super easy to install. Removed door screws, carefully lifted and set aside inside of door leaving wires attached. Reved wire from latchtch switches, attached wires to new latch, put in postion and reassembled.

removed screws from inside plate of dishwasher door. The assembly was hanging free (not clipped to the door). the old handle was easily removed, and the new one was clipped onto the assembly and put back into place. The screws were then replaced.

We had been noticing that the door was becoming increasingly more difficult to open. Extra force was needed. (that's probably why the handle broke in the first place). After the repair, the door opens much more easily.

This was probably the easiest repair we had ever had to do. Not only does the door operate much more smoothly, but we saved the cost of a service call.

Ist Repaired a hole in a rubber hose under the sink. 2nd Removed the 10 foot drainage hose with a regular screw driver (1 clamp at each end of the hose).
3rd Removed the insulation and replaced with the new after disinfecting the entire top and sides of the dishwasher with bleach. This eliminated all bad odor etc. only had to remove 2 plastic brads, 1 on each side of the unit.

Done and no leaks.

First I read all the reports for not cleaning properly already listed on this site. I had to replace the docking station with flappers. When I removed the station I lost the flappers down the water delivery tube just like Jon said I would in his repair post so I removed the water distribution assembly fished out the old flappers and snapped in the new.
But then I figured I might as well check out the accumulator while I was in the tub anyway - I had read that you need Torx screwdriver bit, which I had, undid the screws, pulled out the accumulator screen which was about 80% clogged, discovered I need a new chopper blade and my impeller is disintegrating, put it back together and lost ten minutes looking for the three screws I had incorrectly put in too soon, and now it is cleaning a packed full load like it was supposed to do.
**I love this site - I went to the virtual repairman and it listed every problem I had with this appliance in the order they happened (door latch broke years ago). - I think I am going to look up stuff that I own so I will know ahead what could go wrong with them.

And absolutely NO DUCT TAPE was used in this repair.

The spring mechanism is on the side, so you have to pull the dishwasher out onto the floor. To do that, you have to remove the floor molding (preferably without breaking it) and remove the base coverings (painted metal plates on the bottom of the washer. Unscrew the side gasket plates on the side of the dishwasher (just inside of the door) where it attaches to the cabinet and the screws in the braces at the top (inside the door) where it attaches to the counter top. Now you will be able to slide the washer forward to look at the sides where the door springs are. Depending on the floor, you may have to raise the washer's front feet. They screw up. As you pull the washer forward be careful to not mess up the insulation which drapes over the top and sides. You only need to come out 1/3 of the way to see the sides where there is a plastic wheel at the forward bottom corner. As you move the door up and down you can see the hook where the cable goes and further up the side you can see several notches where the spring goes. Hook the cable and bring it around the wheel and attach it to the spring. To reinstall, just follow these directions backwards. Good luck.

After finding out that the impeller shaft was stripped (plastic) I quickly found the correct replacement on partselect.com by using my model number.
You do not have to remove the dishwasher, if you know what is wrong. But, throw the breaker switch and turn off the water! After removing the spin washer arm, Undo all of the torx screws and pull out the plastic filter looking plates along with the center plastic water jet. This jet provides water for the upper washer assembly. You may have to pop that upper assembly out to protect it from damage.
The black impeller should just pull out if the plastic shaft is stripped. Otherwise, unscrew the small torx head and remove the impeller. You can remove the blade at this time and unscrew the plastic shaft by unthreading it while keeping the motor from spinning. (I shoved a screw driver underneath the dishwasher through the motor. Also the motor is just floating on the rubber gasket and can easily pulled out to accomplish this task. It's heavy and has a plug attached to it. You'll see where you can shove the screw driver. This comes in handy while installing the new shaft, because it is metal. Which is a great, long awaited upgrade for the Maytag Quiet Series. Once you find which shaft to use, (which correct inner thread, course or fine), install it with the great directions that come with the part. Putting all the stuff together is not as bad as one would think, there is only one way for it to go back together. After installation is complete, turn water and breaker switch back on. Run a cycle and listen for the washing cycle against the wall of the washer. If you cannot tell the difference, you can unscrew the white lock arm and insert it into the door. Turn it on and watch how a dishwasher works. Get ready to get a little wet. Towels!

I wanted to get the dishwasher cleaning better and thought that maybe the accumulator needed to be replaced. I figured that I'd swap out all the spray arms as well, just for good measure.

I needed Torx screwdrivers (T15 and T20, I think - not 100% sure on that) and patience because there's really quite a lot of screws to get the accumulator out. Finally got to it and it didn't look damaged, but replaced it anyway.

The spray arms are easy - they just snap in except for the lowest one, that had a plastic nut. I ordered a replacement nut just in case I broke this one (you know how that goes) taking it off. Well, it took pliers, but it came off ok.

In the end, my dishwasher is happy and cleans much better now.

The original brackets that hold the water distribution manifold to the back and top of the tub came off the "X-shaped" plastic posts on the tub walls. That caused the upper wash arm to sag down into the travel of the upper dish rack and was broken off when the rack was pushed in.
I bought 2 new brackets and a new wash arm. The new brackets had a smaller aperature than the originals and fit tightly onto the plastic posts, holding the manifold firmly in its proper location. Replacement of the brackets and the new wash arm took less than ten minutes and required no tools!

disconnected unit (electrical, water, and waste) un mounted from countertop, removed from under countertop, unscrewed hose clamb, cut off wire tie. Attached new hose and wire tie (not included) reversed above steps. Done in about 15 minutes

Not being very computer literate, the most difficult part of the entire venture was navigating your web site. But I finally found the part I needed. I paid on line with a credit card, and received the part within a few days. I popped it in the dishwasher, and it took three days before my son noticed it.
He was surprised and I was proud to say " I ordered it on line."
All's well that end's well.
I would difinately use your service again.

I unscrewed the door panel. removed the plastic cover protecting the dispenser. unscrewed the dispenser (6 screws). I removed the old dispenser and put the new one on and put it all back together. It was pretty easy.

First replaced rubber seal around door, which did not stop the leaking.
Then ordered insulation foam strip and replaced old one, which fixed problem. Put new strip over the old one because tub was slightly warped.
Very pleased with order speed and cost.