MDB9150AWS Maytag Dishwasher - Instructions

I did not move the dishwasher out. It is a fairly tight space underneath, but the water inlet valve is located toward the front, so it wasn't too bad. The steps were:

1) unplug the power and turn off the water to the dishwasher.
2) remove the 2 wire connectors.
3) use the nutdriver to remove the 2 screws that hold the valve to the side of the dishwasher.
4) use a wrench (5/8") to remove the nut where the water goes into the valve. This takes some patience since you can't turn the wrench very far in the tight space.
5) remove the water outlet hose by using pliers to squeeze together the clamp and move it up the hose. Then twist the valve to free the hose and remove it from the valve. The nibs on the clamp are small and take a little time to get them squeezed together. If the hose has been on there a long time, you will have to twist the valve a few times to free it up.
6) now you will have to remove the sleeve that the nut was screwed onto. I had to take the valve to my vise to hold it. Then it wasn't too hard to remove.
7) use teflon tape before you reassemble. Just go in the reverse order.
8) hope there isn't a leak. Mine didn't.

The new water inlet valve seems to have fixed the problem!

Maytag repair man 1 year ago caused most of the damage after I took the front cover off - the repairman broke off most of the screws holding the front panel in place leaving me to replace the front assembly.

The repair was easy - save yourself and do it yourself vs paying someone alot of money to only make it worse in the long run...

Took off old, snapped in new.

It takes about 5 min. to disassembled the lower jet system. As you disassemble, make sure you clean all the filters, and asses the integrity of the filters. If they are broken, you need to replace. Once you get to the impeller, you know it is broken because the lower part is loose. To replace you need to firmly hold the impeller as you unscrew the top screw. If the housing gasket is broken or too loose, replace. Otherwise you will have leak. Refer to your models diagram for proper assembly.

We ordered the replacement part for our Maytag model and when it came we saw that it was different than the original part. The original part had 8 wheels with a higher left hand side. The replacement part had only 6 wheels and no higher side. The replacement part would not pull in and out evenly and was a bit too narrower. We called Parts Select and told them our problem and they are going to refund us in full and take back the part they sent. Alas we will have to buy a new dishwasher. We would use Part Select in the future for replacement parts.
Alice
Cambridge, MA

Open the door all the way. Remove the 7 screws along the perimeter with a Torx screwdriver. Then close the door. Remove the two screws at the bottom of the side of the outside of door panel with a phillips. With the palms of your hand flat on the panel slide the panel up about 1/2 inch and it falls toward you. Follow these steps in the opposite direction to install the new door. I did however replace the two phillips screws last.

Removed four screws on bottom plate. Located repair site on outside of cabinet. Had to hook spring on bottom rear plate by brail. Then attached linkage to spring and ran stiff wire through linkage to raise it above arm. Called a man with stronger but larger hands had him stretch the spring while I guided linkage over arm and into the slot using the wire. Removed stiff wire with needle nose pliers and reassembled front plate.

threw out the broken and put in a fantastically improved new one. very easy (would have done it sooner if I'd known it was that simple to find it online and order it) thanks

I took apart the lower spray arm apart and removed the 6 hex screws. I noticed that the little plastic circle thing had been ripped off the dome-shaped thing. I replaced the part and put it all back together.

Remove bottom rack. Unscrew the retaining ring on the wash arm, remove along with wash nozzle. Unscrew the eight retaining screws on the filter cover and remove (be carefull not to lose the two plastic bushings). Pick off and set aside the wash fan. Remove the six retaining bolts on the discharge housing. Pull up and remove the discharge housing. Remove the gasket (buy a new one, cheap and easier) with small screwdriver. Push gasket into new assembly. Under plastic nut with pliers and take off the plastic bushing that the wash arm rides on. Install new housing assembly with the parts that was taken off in the reverse order. Be carfull when installing the filter cover to make sure the drain outlet is aligned or mated to drain. Gently push down until the filter in down and continue reassembly.


(PS: Never use Sears parts, they extrembly slow as well unable to deliver on time).
Wash your dishes

Was extremely easy to remove that existing rackings(upper and lower), install the new racks and snap in the new spray tower. It now looks like we have a new dishwasher. We are hoping that it will last another 10+ years.
We will recommend your site to friends.

I removed the door panel by unscrewing the 12 allen screws and found that the handle hinges broke & latch assembly locking gear was worn down...just normal wear & tear. this diagnostic process just took 45 minutes...remove the door, identify the problem, remove the parts, reassemble the door. I then ordered the parts online.

Once the parts arrived, it took me less than 45 minutes to re-remove the door, reconnect the 4 wires to latch assembly, snap the latch handle into place, and reassemble the door.

Replacing my dishwasher racks was very easy. I followed the guidance on the PartsSelect.com website for replacing the upper rack. Replacing the lower rack was only challenging when I couldn't figure out how to remove the water sprayer from the old rack and place it in the new rack. A quick search on Google.com and I learned to turn the sprayer counter-clockwise to remove it and then clockwise to put it in the new rack. Worked like a charm! I would recommend PartsSelect.com to anyone. Easy to use, parts came quickly, and I appreciated the guidance from others.

We had had a slow leak on our dishwasher for some time. We were also getting a film left on the dishes and they did not appear clean. Eventually the leak got worse and I had to find the problem. It turned out that in addition to the motor shaft seal leaking, the heating element was out and the installer had done a really bad job, with leaks in the fittings and the wiring not installed properly.

I tried to get the parts locally but they were not in stock and needed a week to arrive. With family coming to visit, I ordered the parts from Parts Select on Monday and they arrived Tuesday. That afternoon, I had everything back together and it is working great.

I aligned the V-shaped tabs on the inner side of the part with the slots in the mating part and simply pulled the old part out (it was already disengaged from the wheels in the metal rail). I then inserted the new part into the slots. One side went in well, but the other side required the part to be bowed slightly to match up the V-shaped tab with the slot. Then the hard part was getting the wheels in position to snap them on. Once in position, it took a bit of effort to engage the snaps in each wheel. I was afraid of breaking the new part. These snaps are very stiff and even with the notch between them there isn't any give, but I was able to apply enough constant, steady pressure to finally get them to snap in without breaking.