MDB8951BWQ10 Maytag Dishwasher - Instructions

I ordered a new replacement basket. The new one is a little different but it fits in the same place and takes up the same amount of room in the dishwasher. It looks very nice too.

unwrapped wheels ,pulled out drawer and easily put on new wheels...as we live way out in the boonies it was great to be able to order parts and have them delivered so fast...easy to fix....

There was no repair to be done. Just replaced the defective basket with the new one.
I got the part two days after ordering it. Great service.

It was so easy to find the right part on the PartsSelect website. I just had to enter the manufacturer (Maytag) and model number and up popped skematics of all the parts available. I just clicked on the drawing of the basket and placed the order. It took less that 5 minutes. The part arrived 4 days later as promised. The repair took even less time than teh ordering. I simply took the old basket out and dropped in the new one.

I'm just happy to know there is a place that has such a user friendly website and stocks so many parts for older appliances. I had my house built in 1992 and several of the appliance are original. Fortunately I always keep the owners manuals for every piece of equipment so the model and serial numbers are readily available.

Most of the time was spent pulling out the dishwasher from under the counter, as a new tile floor had been installed after the DW was installed.

Great pictures of components on this website confirmed what part to order.

Shut off water feed to DW and disconnect power to DW.

Unplug wire connector to old valve (solenoid) and disconnect water inlet hose. Observe that valve is attached to sheet metal bracket.

Remove bracket, with valve attached. Don't remove valve from bracket. New valve comes with sheet metal bracket.

Remove female threaded adaptor (brass) from back of old valve and screw on to new valve using Teflon tape. That is the only piece you need to reuse.

Attached the new bracket (with valve attached) to DW. Attach water inlet hose. Attach plug to new valve.

Turn on water to DW. Check for leaks. Retighten hose connection if required. Run dishwasher. Keep lower panel off for a couple of days to be certain no leaks develop.

Remove the racks top and bottom. The Station D seals are at the far back on the tube that supplies water to the top and middle spray heads. Unsnap the old one and snap in the new - it only goes one way! This will repair the seal aroound the tube that supplies the middle sprayer and restore pressure to all 3 heads. Repalcing the screen accumulator is harder. you need a torx driver. remove the little thumb nut on the bottom sprayer and remove the sprayer. Then remove the tube where you just replaced the D station. (You of course could have done this earlier if you were doing both repairs) then 6 screws on the impeller housing. Now remove the 1 torx screw on the impeller and pull the impeller up and off. Remove the 3 screws on the cover and 2 screws on the accumulator. Clean all the old food scraps that are clogging up the works and reassemble in reverse order. Washer is working again!!

Snapped on new wheels

Ordered replacement basket online at much better price than available localy. When I recieved it discovered that it did not include the handle, but was suprised to see it labeled as "Genuine Maytag Parts" ( I realy expected a knock-off replacement part for the price difference). I was able to remove tha handle from the old basket and install it on the new one. Job done. No problem

Stuck new wheel on, time to find and order part on partselect 2 min, time to open package and install part 1 min.

Total job 3min.

I had to remove the 4 screws holding the toe panel. Then I had to take out the one screw holding the floater switch housing in place. It snapped open to release the floater and that just lifted out. I put the new float in and snapped the new housing on. I put the screw back in to hold the housing in place attached the two wires to the switch and put the toe panel back on. It was all very easy to do and my first home repair went very well. thank you.

This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

After repairing this dishwasher 5 times during the past 8 years this one was real easy: Open door, unscrew inside cover and carefully move over to one side. Unplug soap dispenser, unscrew soap dispenser and remove. Fit new dispenser, reconnect it, put inner cover back in its place and secure it with the retained screws and you are back in operation. Hans.

I noticed there was a filter type of material in the bottom of the dishwasher that had a small tear in it and figured that was my problem. I removed the nut from the sprayer arm at the bottom of the tub, removed the sprayer arm, removed 3 screws of the plastic cover below that. Removed six screws on the plastic cover below that. Removed one screw fron the center of the black pump spinner wheel that allowed me to lift off that cover. Then I lifted out the flowplate assembly. Placed the new part in and reversed the steps. Works like new again! All for about $30...I am not trianed in any way and have no experience in this kind of thing but am motivated trying to avoid a large service bill for a few screws. I am so happy...Thanks PartSelect!

the new dishrack fit right in immediately with no tools needed. Delivery was prompt

I pulled the unit from under the counter. the springs and cables are on the front sides of the dishwasher. I moved the insulation removed the broken spring and cables and replaced them with the new parts. just one side was broken, but I replaced both while I had the unit out.