Quick Question!

Have you ever purchased from PartSelect.com before?

Models > MDB7600AWW > Instructions

MDB7600AWW Maytag Dishwasher - Instructions

All installation instructions for MDB7600AWW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the MDB7600AWW
751-765 of 1,919
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

no water being pumped thru any of the 3 wash arms

  • Customer: Dennis from Raymond, NH
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 0 of 1 people found this instruction helpful
Removed all the screws holding the shroud, filter, wash arm, etc. Installed new shaft and chopper blade, then reinstalled impella on new shaft as described on the easy to follow instructions.

track was spread open and the stopper would fall off

  • Customer: Paula from Freeland, PA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
just had to remove the stoppers and slide the track on and then replace the new stoppers.
most of all i was pleasantly surprised at how fast the parts arrived. i ordered them thursday morning and i was installing them friday morning .

Door Handle broke

  • Customer: Alex from Columbiana, OH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
The dishwasher door would not open and it appeared that the handle was broken. Ordered new door handle assembly which took one day to get by mail.

After squeezing the handle hard and applying force to pull upen open the door, the door came open.

Turn off electric power to dishwasher

Remove all the scews around the door frame.

Carefully pulling ccver back,remove the two screws from the handle assembly that hold it to the door.

Rather than pulling the wires off the microswitches, I removed each microswitch with wires attached by applying pressure on the two plastic tabs and slowly wiggleing the microswitch off the assembly.

On the new assembly, I removed the existing microswitches and put them in a bag for future use if needed. Snap the old microswitches in to place onto the new assembly.

Screw the new assembly to door and test latching. Then put all the screws back in the door.

Reapply power and test door for opening and also electrical functioning of the microswitches.

door latch snapped off

  • Customer: Julian from Dunkirk, MD
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 1 people found this instruction helpful
After reading other stories ref. same problem on here, I decided to go ahead and and try the repair myself. It really was as easy as described. Plus I honestly believe the replace ment latch assembly from here is a much stonger and better designed part than the original factory part!

Broken wheel on adjuster

  • Customer: Robin from Champlin, MN
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
It was so easy to install this part. I did have to buy a star screwdriver because I only had a flathead and a Phillips head, but I just took the part to the hardware store to make sure I bought the right driver. Once I had the right tool, installation tool less than 10 minutes. It was just a matter of removing the old part and putting on the new part -- 6 screws and your done. Very happy with this part.

Basket was worn out and the bottom was falling apart

  • Customer: James from Georgetown, MA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
Replaced the basket which was difficult to find

door latch broke

  • Customer: MARCOS from LYNWOOD, IL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
I first shut of the circuit breaker just to be safe. I removed the screws holding the inside door panel to the door .Lifting the panel I was able to pull out the damaged part. Removed the 2 plugs on the old part attached them to the new part, putting the new part back in place. Replaced the screws and I was done. Easiest repair job that I've done in a while. The cost of the new part with shipping was less than $30. I had called a Maytag repair shop and they were going to charge me $125 to $200.

Door was hard to open after pulling handle

  • Customer: Edward from Kokomo, IN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 1 people found this instruction helpful
Gave the scrwe driver to my daughter and she fixed it. removed eleven srews took off the panel and removed the connectos with a pair of pliers removed latch. replaced the latch and handle connected the wires replaced the panel closed the door turned on the dishwasher, it worked

couldn't get it to start cycle, then it wouldn't latch

  • Customer: James from Madison, WI
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 1 people found this instruction helpful
Remove 11 tork screws, pry off wires from the 2 switches with screwdriver, then put in new part and close it back up. See where they corrected the design flaw in the original part.

Bottom of the silverware basket had broken

  • Customer: Kimberly from St. Paul, MN
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
I removed the handle from the old silverware basket and put it on the new one. As easy as that!

Door latch was broken and hard to open

  • Customer: Mike from Bend, OR
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
What a simple fix, wish the part was manufactured better, so many people have to fix it. First of all, switch the breaker off, there is power to the dishwasher and maybe to that part, I did not check, be on the safe side and hit the breaker. Open the door and leave it all the way open to remove the 11 screws? Removing the torx screws, not sure what size they were, could be 10 or 15. Lift up the panel facing you any simply pull out the latch. With a large screwdriver, put the blade in between the two electrical contacts and pry the connectors off the contacts. Throw away the old latch and connect the contacts to the new part. Place the latch in position and screw the panel back in place. Remember to turn the power back on and you’re done. I took me longer to get the tools together than to fix the dishwasher - about 10 minutes altogether.

Broken door latch

  • Customer: Gene from Round Rock, TX
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
Removed inside door panel, door latch/handle assembly and 2 plug-on wires to switches.
Installed new door latch/handle assembly, switch wires and door panel.

Replaced Door Latch

  • Customer: Deborah from Bradenton, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 1 people found this instruction helpful
I opend the door and viewed how the latch was positioned and secured. All the SM screws along the door seal had to be removed. This unsecured the inside door skin and revealed the old latch. No additional fasteners needed to be removed.

Wires were secured with a snap-on type pole system. It took some strength to pull them off. However, I was sure to place each on the same pole of the new latch.

The new latch went into its place and was auto-centered correctly on the door fixture designed for the part. Skin was resecured ... good to go!

Handle broke

  • Customer: William from Red Bluff, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 1 people found this instruction helpful
Unscrew 10-12 screws from back panel of door. Unplug the electrial. There were two plugs that fit very tight, Hardest part of the repair, Had to use pliers to get the dam things off. ( 2 minutes)
Plug in new handle, set in door, and replace all screws. about 10 minutes from start to finish. If you use a hand screw driver and 10 minutes.

Replace broken silverware basket

  • Customer: Raymund from Cedar Rapids, IA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
The only tricky part was taking the carrying handle off the broken basket and installing it on the new basket. The handle has three alternating hooks (two on one side and one on the other) that snap into slots in the center partition of the basket. I used three butter knives to push out the hooks from the slots so that I could remove the carrying handle. Once removed, the carrying handle snapped into place on the new basket fairly easily.
All Instructions for the MDB7600AWW
751-765 of 1,919