Quick Question!

Have you ever purchased from PartSelect.com before?

Models > MDB7600AWB > Instructions

MDB7600AWB Maytag Dishwasher - Instructions

All installation instructions for MDB7600AWB parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the MDB7600AWB
1,021-1,035 of 1,921
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Wheel came off rack adjuster for upper tub

  • Customer: Gregg from East Peoria, IL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
Easy switch of parts, hardest part was finding the right torx size to match.

Broken latch handle

  • Customer: Bill from Columbus, OH
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
So easy a Cave man could do it. Remove 8 screws, prop open inner cover, lift out old latch unit, unplug power switch leads and replace. I did this with the power on but recommend turning it off for your safety. Very easy and part arrived in 2 days.

Broken Door Latch

  • Customer: Alan from Palatine, IL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 1 people found this instruction helpful
First I threw the circuit breaker for the dishwasher to cut power. The I used a torx driver to remove the 11 screws holding the inside door panel to the door frame. The top 2 of these also held the Door latch in place. I used Needle nose pliers and standard piers to unconnect the two electrical connections from the latch assembly. Swapped out the original (broken) latch with the new assembly, reconnected the two connectionas and replaced the 11 screws. Very easy. Very quick.

door handle broken and wouldn't open

  • Customer: leobardo from kansas city, KS
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 1 people found this instruction helpful
got the part off your website and I have to say that the little section that tells me that the dishwasher I had and it's most common problems really helped me get the right part. I wasn't sure if it was the handle or the mechanism inside that latches the handle but I got what was the most common problem according to your website and it was fixed. great and resourceful website. I will be shopping here from now on when I need parts for any of my appliances if you have them. You have been bookmarked!

Door handle broke and was hard to open

  • Customer: Frank from Ramona, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
It was so easy to install. It came with the handle and switches already put together for me. I removed about
ten T-20 Torx screws from the inside cover to expose the handle mechanism. When you remove these screws it also releases the handle assembly. The hard part if you want to call it that, was removing the wires off the old switch assemblies. A small screw drive works fine to pry them off. Re-connect the two wires and install the cover and your done. I did a lot of checking and PartSelect.com had the best price anywere.

The handle broke

  • Customer: John from Sumter, SC
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 0 of 1 people found this instruction helpful
Very simple repair. removed the torx head screws around the perimeter of the door's inside cover. Pulled (with some effort) the connectors off the old handle. connected them to the new one and re-installed the screws. As the screws are mounted in plastic and sheet metal take care not to over-torque them.
John

Broken Handle Latch

  • Customer: Dustin from Tigard, OR
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
New part came all as one assembly, reconnected the elec wire hubs - it was all quite simple.
The part arrived even a couple days early.

Latch Handle Broken At Hinge

  • Customer: Rose from FROSTBURG, MD
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
Turned off the power at circuit breaker. Used a 'star' fitting for screws on the inside of the door. Two short pieces of 1" x 2" about 8" long were need to keep the inside of the door piece seperated from the outside door. Wiring on the inside would not allow a full lift of the insides of the door. The plugs to the old unit were not easy to get off. Some effort and the help of a screw driver or pliers are needed. Putting back the two plugs is easy and the latch assembly can easily be put in place. The latch assembly is kept in place by the same screws that are used for the rest of the inner door when putting it back together. The procedure was easy. The shipment of the part needed was very fast! A great amount of money was saved! (Rose, my wife, ordered the part and I (tony)did the rest)

Handle broke

  • Customer: William from Prospect, PA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 1 people found this instruction helpful
Instead of just buying a handle, you can purchase the entire latch assembly. Check your dishwasher door to see if you require a torx screw driver. If you don't have one, consider buying a folding set so you will have numerous sizes for future repairs on other items. Turn off the breaker to the dishwasher. Use a torx screw driver or bits to remove the inner cover of the dish washer door. Then unplug the leads on either side of the assembly. Mark the outside of the plugs so you don't get them switched. Use a small flat screw diver and/or pliers to unplug the leads. Plug the leads into the new assembly, and reinstall the torx screws for the inner panel. Easy fix.

Door handle broke

  • Customer: Frank from Papillion, NE
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
It was so easy I just removed 10 screws and removed 2 wire clips and pulled out the old handle and the replaced the new one. I have no idea how much I saved but I would guess close to a hundred bucks. Thanks PartSelect.

Door Handle broke

  • Customer: John from Vilonia, AR
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 1 people found this instruction helpful
After reading the installation instructions on line I diagnosed the solution and order the part from PartSelect. The part arrived on the promise day. Having read what others wrote about their installations, installing the part was possibly the easiest repair I have ever made. I will definitely remember PartSelect my future needs.

Door handle Inop

  • Customer: Joseph from Melbourne, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
Unscewed 11 scews, unpluged electrical connections, Of course, made sure power was diconnected,replased hander according to website directions, very simple, took ten minutes. Thanks. You saved at least $100.00 dallars

Broken Latch/Handle Assembly

  • Customer: Massimiliano from Burlington, IA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
Disconnected power to dishwasher. Removed screws holding inside cover of door. Lifted door cover, unplugged wires from micro switches on handle. Removed broken latch/handle assembly and replaced with the new one. Re-installed door cover.

Handle on Dishwasher broke

  • Customer: CRAIG from PROVO, UT
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
The only problem I had was the miro switches, didn't have the tool to release the exsisting wires on the old switches so I had to reuse the old ones just by swithcing them to the new handle and every thing works great now. If anyone knows what tool that I need to get the wires off the old mirco switches let me know. craign84601@comcast.net

latch broken

  • Customer: robert from mount Airy, MD
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
Turn off power(curciuit breaker) to dishwasher, Removed screws from around inside door edge, then pulled front away slightly pulled latch assembly out about six inches, disconnected wire connectors from handle asembly, discarded old assembly, attached connectors to new assembly, reinstalled in place, replaced screws, turned power back on, closed door repair complete and works great.
All Instructions for the MDB7600AWB
1,021-1,035 of 1,921