Quick Question!

Have you ever purchased from PartSelect.com before?

Models > MDB7600AWB > Instructions

MDB7600AWB Maytag Dishwasher - Instructions

All installation instructions for MDB7600AWB parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the MDB7600AWB
61-75 of 1,921
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

silverware basket broken - replaced with new one

  • Customer: Linda from Owasso, OK
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 14 of 15 people found this instruction helpful
I was able to remove the old handle and place it on the new basket - using only a screw driver.

Latch on dishwasher had broken.

  • Customer: Jason from Littleton, CO
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 15 of 18 people found this instruction helpful
After purchasing some torx head screwdrivers, it was easy to remove the front door of the diswasher and see that a few tiny plastic pieces had broken on the latch, rendering the entire dishwasher unusable. I found all of the broken pieces, and it took about 5 minutes to order replacement parts from partselect.com. What a great website! The schematics made it simple to identify exactly the parts I needed.
The parts arrived promptly, fit perfectly, and installation was a breeze.

water was dripping from the bottom of the front loading door. Over time this had seeped into the insulation foam strip and formed a solid encrustation within the foam strip.

  • Customer: Dan from Clarkston, MI
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 14 of 15 people found this instruction helpful
The real cause of the leak had nothing to do with the foam strip. The latch for the front loading door at the top needed to be adjusted to hold the door in tighter to the rubber door seal. This simple adjustment stopped the leak but since the foam seal was all encrusted with dried detergent from probably years of absorbing the leak, I replaced it with your new foam strip. I used a screw driver with torx bit and removed the stainless screws holding the inner door to the outer door. Once these were separated I removed the old foam strip using a putty knife and lacquer thinner. Placing the new strip onto these cleaned surfaces was the easiest part of the whole repair.

My dainty darling wife using brute force brike the latch assembly by taking out her frustration on having to do the dishes again. Although broken the dishwasher still worked, but was difficult in opening. Trying to open it one evening her brute force tore the plastic on the panel near the latch. Now

  • Customer: Ron from Scottsdale, AZ
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers
  • 14 of 17 people found this instruction helpful
First , unplug your dishwasher from the outlet.Then remove the 9screws all the way around the inside of the door,followed by removing the 2 screws that hold the latch, 2 screws that hold the panel and 2 screws that hold the black case containing the electronic circuit board. You need to open up the black case in order to remove the thin cable that connects to the circuit board and which makes everything work. (You get a new one allready attached with the new panel). Next go to the latch assembly.You alsoneed to unhook the black & white leads. Take your time here and pull them straight back and slowly with a pair of needlenose pliers. They are stubborn so just take your time.To be safe I drew a small diagram to make sure that I hooked the white back to the right connection.
Once the part s were received , I put the new panel on, connected the cable to the circuit board, closed the case and put the screws back in. Next , I put the black & white wires back on the switch ( based on my diagram) , put the 2 screws in the latch locations and then put the remaining screws back into the inside door. Plugged it in , tested it, and everything worked just fine.
So far the wife hasn't used her herculean strength again. This is a Maytag & things aren't supposed to break.
Last note: Your telephone person was a jewel. The latch was shown as NLA (No longer available). She took the time when I called to follow up on the part number and find another number made by another company by special order. Absolutely first class in my book. Kudos to her.
Thanks again, service was good and delivery was within 5 days.

Dishwasher handle broke

  • Customer: Christy from Warm Springs, GA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 14 of 17 people found this instruction helpful
This was a very easy repair. Before I did anything, I flipped the breaker for the dishwasher and tried to turn the dishwasher on to make sure it had no power going to it. Once I was certain the power was off I removed the hex screws (there are 11) on the inside of the door panel using the hex screwdriver. Lifting and holding the inside panel up, I then used the pliers to pry the old latch assembly out of its metal prongs. Then I replaced the old latch assembly with the new one, pushing the metal prongs (by hand) into the slits of the new latch assembly. Last, I lined everything up and screwed the door panel back in place. I flipped the breaker back on and activated my child lock to make sure I had power. The handle worked perfectly. Quick and easy fix!
I ordered the part with 3-5 day delivery and actually received it in 2 days! I'm extremely pleased with my partselect.com experience and highly recommend using them for all your appliance parts needs!

broken latch

  • Customer: eric from newark, OH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 14 of 17 people found this instruction helpful
i ordered the parts on sunday night at about 9pm. the parts arrived on tuesday afternoon! i removed the screws on the inside of the door, then removed the latch assembly and unplugged the two connectors. i then plugged in the new latch assembly and replaced the screws. i accidentally ordered two parts i did not need and received an email twenty minutes after i asked how to return the unneeded parts descibing the return process. i have already told three people how awesome your company is. anytime i need appliance parts i won't look anywhere else. you have a customer for life!! thanks for everything.

Door leaking, handle broken

  • Customer: John from Warren, MA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 13 of 15 people found this instruction helpful
Door gasket was easy out and in using the white mark on the seal to line it up with the center. The latch came with the handle so I returned the extra latch assembly that I ordered. Super easy to install. Removed door screws, carefully lifted and set aside inside of door leaving wires attached. Reved wire from latchtch switches, attached wires to new latch, put in postion and reassembled.

Upper Dish / Glass Tine

  • Customer: James from Wolcott, CT
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 16 of 24 people found this instruction helpful
Upper dish rack with dish / glass fold away tine has two broken latches, this situation is causing instability. Went to partselect for schematic and found what looked like the necessary replacement latch/s on print and ordered all latches. Received parts only to find they were the wrong ones. Evidently they are the parts for the bottom dish / glass fold away tine. Removed upper tine and still looking for the actual replacement parts on the schematic with no luck.

broken wheel on the top pull out rack

  • Customer: Mike from Axtell, TX
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 11 of 11 people found this instruction helpful
First I placed a cutting board under the rack to hold it in place while I took the five screws out of the bracket holding the T shaped bracket in place. I then just switched out the old for the new and guided the bracket into the side mounting piece and placed the end cap back on. Double checked the tightness of the screws and it was done.

Top rack wheel broke, dishwasher didn't run right.

  • Customer: Michael from Zillah, WA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 15 of 23 people found this instruction helpful
Removed the rack from the dishwasher. Removed Torx head screws holding the stabilizer in place. Pulled the two sections apart. Cleaned out the junk and replaced the stabilizer bar. New one had wheels with steel axles, so this should last much longer than the plastic ones. Put the rack back into the dishwasher. Ready to go.

The impeller was not spinning. There was no washing water.

  • Customer: Brian from Portland, OR
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Wrench set
  • 11 of 12 people found this instruction helpful
After finding out that the impeller shaft was stripped (plastic) I quickly found the correct replacement on partselect.com by using my model number.
You do not have to remove the dishwasher, if you know what is wrong. But, throw the breaker switch and turn off the water! After removing the spin washer arm, Undo all of the torx screws and pull out the plastic filter looking plates along with the center plastic water jet. This jet provides water for the upper washer assembly. You may have to pop that upper assembly out to protect it from damage.
The black impeller should just pull out if the plastic shaft is stripped. Otherwise, unscrew the small torx head and remove the impeller. You can remove the blade at this time and unscrew the plastic shaft by unthreading it while keeping the motor from spinning. (I shoved a screw driver underneath the dishwasher through the motor. Also the motor is just floating on the rubber gasket and can easily pulled out to accomplish this task. It's heavy and has a plug attached to it. You'll see where you can shove the screw driver. This comes in handy while installing the new shaft, because it is metal. Which is a great, long awaited upgrade for the Maytag Quiet Series. Once you find which shaft to use, (which correct inner thread, course or fine), install it with the great directions that come with the part. Putting all the stuff together is not as bad as one would think, there is only one way for it to go back together. After installation is complete, turn water and breaker switch back on. Run a cycle and listen for the washing cycle against the wall of the washer. If you cannot tell the difference, you can unscrew the white lock arm and insert it into the door. Turn it on and watch how a dishwasher works. Get ready to get a little wet. Towels!

The regular wash button and the start button would not light up.

  • Customer: Todd from Waterloo, NE
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 13 of 18 people found this instruction helpful
Just had to remove the screws from the inside of the washer. Took the screws off of the control panel. Disconected the wires (easy) then replaced with the new part. Much easier than I thought it would be, I might be thinking of doing repairs for other people now... thank you so much

Dishwasher heating element bad

  • Customer: Gary from Indianapolis, IN
  • Difficulty: Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
  • 11 of 13 people found this instruction helpful
I could not reach the heater element nuts from under the dishwasher so had to pull out the dishwasher. I removed the screws around the front of the dishwasher and pulled it about half way out before the water inlet pipe and the electrical wires stopped me. I shut off the water, unhooked the copper pipe, and unhooked the electrical wires (shut off circuit breaker first). Pulled the dishwaser out so I could remove the element nuts and wires to the element. Removed the old element and installed the new one - the old nuts would not fit. I went to a local appliance parts store and found that my element is no longer made. I had the correct replacement element but you need to order the nuts also. Luckily, the local store had a small brass nut that worked. Reattached the electrical wires to the element, pushed the dishwasher half way in, reattached the water inlet and electrical wires, pushed the dishwasher all the way in and scewed back into the cabinets. All is well now and the dishwasher is working much better.

Dishwasher not draining

  • Customer: Darrell from Snellville, GA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 10 of 10 people found this instruction helpful
It was my first time repairing a dishwasher. I was a little worried. I also wasn't sure about how to remove the drain pump. Well, the hardest part was just getting the dishwasher out from under the counter. I did find a crimp in the drain line that probably contributed to the original pump going out. I fixed that, removed the old pump by removing one screw holding a stablizer bracket and twisting the pump connection. The original bracket is needed, so I removed it from the old pump, attached it to the new pump and reversed the removal process and secured the pump by reattaching the stabilizer bar with the single screw. I then slide the dishwasher back under the counter. Runs great. Easy repair. The part was shipped and delivered on time. Very impressed with the process and will order my appliance parts from you in the future.

Plastic door latch broken

  • Customer: Gary from Saint Joseph, MO
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers
  • 10 of 10 people found this instruction helpful
1)Turn off breaker to dishwasher.
2)Remove screws that fasten plastic liner to outer door with allen wrench.
3)Disconnect two wiring connections to latch assembly; this was toughest part of project, had to use pliers to get metal connectors our of sockets.
4)Connected new assembly and screwed door back together.
All Instructions for the MDB7600AWB
61-75 of 1,921