Quick Question!

Have you ever purchased from PartSelect.com before?

Models > MDB6000AWW > Instructions

MDB6000AWW Maytag Dishwasher - Instructions

All installation instructions for MDB6000AWW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the MDB6000AWW
646-660 of 878
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Door Spring Linkage Broke

  • Customer: Todd from Claymont, DE
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
simply replaced linkage and reconnected. Very easy

Broken dishwasher basket.

  • Customer: John from Darien, CT
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Threw out the old broken one and this fit perfectly!

I got my parts from you

  • Customer: Angela from Whitehall, WI
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I haven't gotten to our rental to get the job done yet but it should go real easy because the broken one came off real easy these should go on just as easy. Thanks again for the parts

The bottom grid of the silverware basket separated.

  • Customer: Irene from Holmdel, NJ
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Just ordered a new one, which came VERY quickly, and put it in!

Replaced rusted rack

  • Customer: Richard from Olympia, WA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Remove rack, untwist spray tower and remove wheels (these have easy to remove plastic clips). Put tower on new rack and replace wheels on the NEW dishrack that were brocken on arrival with wheels from old rack. All done in 5 minutes.

Leaking between door and bottom panel

  • Customer: Jamie from Polson, MT
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Removed the old strip - cleaned the channel and installed the new gasket. Soooo easy. Unfortunately it's still leaking so now I'm ordering the gasket kit. Should have done it to begin with - like everyone else does!!!

noisey belt system

  • Customer: thomas from west sacramento, CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Socket set
  • 0 of 0 people found this instruction helpful
The ironic thing is it wasn't broke! I had ordered new rollers, new belt and new tensioner, before I took the front off. The video was helpful. The tough part was reinstalling the tensioner as it did not screw down. But live and learn. I set the tensioner in place and used small wire to bring it over to the moter drive, then assembled the new belt together and cut the retaining wire.

Door would not come up as spring assembly broke

  • Customer: Paul from Perrysburg, OH
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
Ordered a plastic part from supplier and installed the part, door works fine now.

The pop-up prongs for plates vs bowls had failed due to broken peg clip

  • Customer: Robert from Clearfield, UT
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Removed lower dish basket, removed the two original peg clips,then snapped in the two new peg clips and adjustable prong assembly worked as required. No further problems experienced. Appreciated the rapid receipt of parts. Will definitely remember this web site for future appliance parts.

Motor runs, no water sounds, poor cleaning

  • Customer: Harlan from Santa Maria, CA
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Disassembled spray arm the way the website describes. Found an amazing accumulation of scale and soap scum. Everything was seriously gunked up. Cleaning and rodding out the spray arms and pump housing screens takes a minute. Be careful not to break or puncture the screens. Dont try slapping the pump housing filter on the driveway. Its brittle and will break. Suggest buying a new one anyway. Its nearly impossible to clean. Simply clean it all up and re-assemble. Oh and bask in the praise from your wife.

Water leaking out the lower right corner of the door.

  • Customer: Edward from Leominster, MA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Just removed the old door gasket and the 2 water deflectors.Too easy.

I Needed To Remove And Replace The Sprayer

  • Customer: ROBERT from GARDEN GROVE, CA
  • Difficulty: Really Easy
  • Time to Complete: More than 2 hours
  • Tools Required:
  • 0 of 0 people found this instruction helpful
After viewing usless videos, I finally read other comments and discovered how easy it was to just twist the sprayer.

Dishwasher would pump the used water out.

  • Customer: Robert from Bandon, OR
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Changed float switch to no avail! Ladeled out the water. Disassembled the entire pump unit inside down to the motor shaft and checked all pieces for trouble. Could find nothing wrong. Now trying to determine if the problem is in the timer or motor.

Cracked Silverware Basket

  • Customer: Mary from York, PA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Easiest ever. Recycled the old one and put the new in its place. We are trying to place the silverware in, rather than dropping it in. It was suggested in the video from this website.

Plastic door spring link was broken on one side

  • Customer: Steve from Desert Hot Springs, CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
Watched video, very helpful. Pulled dishwasher out a foot from counter, which was the most difficult part due to tight fit, carpet, and copper tube water connection. Once the washer was out it was easy to replace the linkage and while it was out did both sides.
All Instructions for the MDB6000AWW
646-660 of 878