MAV6200AWW Maytag Washer - Instructions

I put the washer on the spin cycle and could see that the tub wanted to move. While it was trying to spin I leaned the washer forward and saw that the motor was spinning and the belt was turning, but the tub wasn't. Did some reading and it was the thrust bearing. I ordered the part and replaced them (very easy, follow the directions that come with the set). After install, the tub would spin.

You do not have to remove any water lines to do this repair. Just unplug the machine from the electric outlet and tip it up on its back to make the repair. I removed the old belt and parts per the instructions. The new kit does not look like the old one. Make sure you mark the minimum and maximum marks with a sharpie on the plastic pulley before intalling it. This will help line up the cam bearing to test the spin cycle. The repair kit says to use the thickest washer but mine would not fit on so I used the thinner washer. Keep the other washer so that in the future if the plastic part wears down and you have spinning problems again you can replace it with the thicker washer. Also make sure you buy a new belt and replace the belt. I loaded it up with a full load of jeans and it works great.

I am a woman (small) very low on funds and could not see myself spending $140 plus parts. I found your website and was able to determine the cause of the problem, since it did not appear the solution would be too difficult to accomplish I ordered the two parts that could be causing the problem. The parts were delivered in 2 days and I was able to do the repair in less than 15 mins I only used the lid switch. The old parts do just snap out and you snap the new one in. Thank you so much for your site. In these economic times you are a godsend.
Keep up the great work and again thank you!

I used the instructions from others and modified them with tips and details based on my own experience:
1. Unplug the power, turn off the hot/cold water valves and disconnect the hot/cold water hoses and drain hose. Tip: plug the drain hose with some paper towels to keep the stale water from dripping on your floors.
2. Move the washer to an open area like a garage, and position it near a wall (or have a helper on hand who can help you prop up the washer top later). Tip: to simplify things, you’ll want to avoid removing the top completely. Removing the top completely involves removing the inlet water hose and all wires leading to the control panel and the door switch.
3. Lay the washer on its side and remove the drive belt from the bottom of the washer.
4. Place the washer upright again and remove the lower rear panel held by eight ¼” hex screws.
5. With the rear panel off, you will see a black drain hose that connects the tub to the pump. Remove the hose at the pump with a pair of pliers. The hose is just held on with a spring clamp.
6. Remove the front panel: pry the top off at 2 front hinge points with a flat head screwdriver. With the top up, remove two 5/16” hex screws holding the front panel and remove the front panel.
7. Remove suspension springs: To easily remove the suspension springs, you will need about 12 quarters (or nickels) for each spring. I hope I can describe this part clearly. For the removal of each spring, tilt the top of the tub away from you as far as you can in order to stretch out the spring. Now insert coins between the gaps in the spring coil, alternating the coins on each side of the coil to keep the spring coil straight. Then tilt the top of the tub back toward you to release the tension on the spring and you should now be able to easily unhook the spring from the tub. The coins keep the coil stretched out for re-installation later. Repeat for the other 5 coils. Note: Others have mentioned using a metal electrical box for this, but I can’t visualize it.
8. Now raise the washer top and prop it against the wall (or have a helper hold it vertical). Follow the small clear “water level” hose that runs from the control panel to the rear of the tub and disconnect it from the tub. It is just held by a small spring clamp.
9. Remove the tub assembly. Remember the position of the tub before you take it out. Place a couple of 4”x4”s (or equivalent) on the ground to support the edges of the washer tub when you turn it upside down. With the springs removed, the drive belt off, and the water level hose and drain hose detached, you should be able to simply lift the tub assembly out. Lay the tub upside down on the 4x4s.
10. Remove the snubber ring: There is no need to remove the flywheel if you have a small or fairly shallow socket (or an angled open end wrench). My small socket worked fine. As others have mentioned, remove the snubber ring by backing out the six 5/16” hex bolts that hold the snubber ring in place. Do not remove the bolts completely. The metal retaining plate is supposed to be under spring tension, but mine did not rise when I loosened the bolts, so I had to pry it up slightly with a flat screwdriver to form enough of a gap to insert the new snubber ring. Make sure the new snubber ring is seated evenly and re-tighten the 6 bolts.
11. Reinstall: Place tub back into the cabinet, reconnect the thin water level hose, reconnect the drain hose at the pump.
12. Spring re-installation: As you hook each spring to the tub, make sure the bottom of the spring is hooked properly to the bottom of the cabinet. Then tilt the top of the tub away from you to stretch the spring out in order to remove the coins. Then tilt it back toward you to remove the tension. Repeat for the other 5 springs.
13. Re-install the front panel and the rear panel and place the washer top back in place.
14. Lay the washer on its side to reinstall the drive belt.
15. Hook up your hot/cold water, drain hose, tur

shut off supply lines, remove cover on back of washer, remove drain hose from pump,inlet and exit. remove belt underneath washer from pump. remove 3 assembly screws. remove pump. set new pump in place. rescrew pump to washer. reatach inlet and exit hoses to pump put belt back on under washer put cover back on back of washer. turn supply flines back on. should work like new

The washer (bought 9 years ago) suddenly started squealing (metal on metal sound) during the spin cycle. After turning the washing machine off and unplugging it, the washer was tipped back and propped up on a milk crate to see the belt on the bottom. There was some rubber dust from the belt, so something had seized-up to some degree. The belt was removed and each pulley was tested to see if it made any noise. Upon spinning the pulley of the water pump a scraping sound was heard. Definitely not as loud as when the washer was on, but it probably would have been if it was spinning faster.

The washer was put upright again and the lid taped to the top to secure it before lifting the top. The top was opened by sliding a putty knife between the top and front panal near the left and right corners. There are two metal clasps that will release the top with gentle pressure, do not pry on the top. The top was lifted up and set back gently so as not to bend or break the hinges. There are two small screws on the upper inner right and left side of the front panel that were removed using a nut driver in order to remove the front panel.

With the front panel removed the water pump was visible in the front, lower left hand corner on the base. The two hoses were removed from the pump by moving the hose clamps up the hose, using pliers to loosen the clamps and then pulling off the hoses with a slight twisting back and forth. I put a few towels around the pump before removal to soak up the water that came out. The three bolts holding the pump in place were removed using a socket wrench and the pump removed.

The new pump was replaced, hoses were put back on, front panel replaced and the top relatch. The washer was tipped back again to get to the bottom to put on the new belt.

That was all. It worked great.

Notes:
1) Several people had mentioned having similar problems with the water pump and had observed a metal ring that had been pushed up where the pulley is connected to the shaft. I also observed this on the sqealing pump. The metal ring seem to work its way out and scrape on the metal mounting plate on the bottom of the pump. So if you see this ring, it is probably the pump.

2)I cleaned the pulleys since there was some rubber dust on them. Also you can remove the belt easily by pulling it slightly off the large pulley and then turning it off. When putting the belt back on, put it around the small pulleys first and then start it on the large pulley and turn it onto the large pulley. More leverage with the large pulley.

..First I sought the source of the water leak, by removing the louvered panel on the rear (4 nut headed screws hold it in place) and observed for water leaks during a wash cycle. This required that I re-position the washer and route the fill and drain hoses in order to stand behind the washer during its cycle to observe through the rear panel opening.

...There was no visible leakage of any of the hoses or connections but I could see the water puddle on the floor was coming from under the water pump located in the front corner.

...I wasn't able to peel the sides off the washer. I disconnected the rear hoses for hot and cold water and the drain hose. I removed the plate on the rear that orients the drain hose.

...I tilted the washer 90 degrees to its front using 2 x 4's to cushion the front so the machine would not be scratched.

....I removed the drive belt underneath. It was easy to remove by hand and did not require loosening screws on any of the pulleys.

...I disconnected the black exhaust hose from the tub with a screw driver and the white drain outlet hose with water pump pliers.

...I then reached into the front corner of the machine through the opening in the back and removed the water pump which is held in place by 3 nut head screws. I used a ratchet set to do this.

...I observed the water pump which is almost all molded plastic. The bushing area in the center attached to the impeller appeared to be wet and rusted. I assumed this to be the source of the water leak. I found the replacement on line at PartSelect site and ordered it. It was much cheaper at PartSelect then other sites.

....When the replacement pump arrived 2 days later , I compared it to the pump I removed. It matched physically including the pulley so then I installed it and re-assembled the washing machine in the reverse order from disassembly.

...I left the louvered panel off and observed the water flow for leaks during the first wash after re-assembly.

...There were no internal leaks and no puddling on the floor, so I replaced the louvered panel and put the washing machine back in place.

The water pump was a bit noisy during the 1st load
but otherwise the machine ran well. After the 1st load the pump is quiet and the machine runs just as it did before the puddling occurred. It is fine.

After having done this I can say, it was uncomfortable and cramped to reach in through the rear panel opening to remove and replace the water pump. But I could not find a way to lift the top of the machine easily so I could removed the side panels to have better access to the water pump and hoses. If anyone knows a way to do that without unplugging and removing the electronics panel, that would be useful information. Please post it.

It can be done the way I described here because I did it, but that may not be the easiest way if the side panels can be easily removed it would probably be an easier repair.

Unplugged Machine, Turned Off Water, Disconnected water and drain hoses. Let water run from hoses ino bucket.
Removed back plate where drain hose goes into back of machine. Used pliers to close the clamp holding to drain hose to remove it. I stuffed the exposed water pump opening with towels to keep water from spilling.
At this point I leaned the machine over on its front so the back of the machine was facing skyward. I placed a towel over the motor in case water spilled it would not get on the electrical components. I removed the belt on the bottom of the machine from the water pumps pully. I then removed the three screws mounting the pump to the bottom of the machine. I disconnected the other hose from the water pump that comes from the wash tank with the pliers. Once disconnected I stuffed the ends of both with towels to keep water from leaking out.
I took the new pump and connected the hose from the washer tub with pliers, mounted the pump back to the bottom of the tub with the three screws, replaced the belt, and reconnected the drain hose, and took the towel off the motor. I then replaced the back plate and set the machine upright. I connected all the hoses back up and plugged it in. It worked great. If you spill water on the motor you can dry it with a hair dryer.

Replaced cam in lid. Simple repair, even a novice could preform.

Unplugged and removed the drain and supply hoses from the back; some water will run out so be ready for that. I laid the machine down on two 2x4s to keep from crushing the supply and drain nipples. Just follow the instructions included with the parts, all steps are straight forward accept for two things: 1. they talk about pulling down on the transmission shaft to slip on the retaining clip. With only the end of the shaft sticking out there isn't much to grab on to. I found by using a thin blade scraper inserted into the retaining clip groove, prying downward on the shaft I could then get a regular screwdriver blade into the same groove and expose the entire groove and slip on the clip. 2. they talk about "Adjusting Brake Disengagement" after studying this for a while it just refers to which thickness of thrust washer to use. After trying both the .062 and .032 I found that only the .032 would allow the retaining clip to engage. Rechecking the brake disengagement, everthing seemed to work fine. The machine now has a stronger spin cycle and even bath towels are ready for drying after the normal spin.

After of hours on the internet looking for answers ( Without any success ) I accidently came upon the solution. There's a small hidden cover plate on the front of the knob that just looks cosmetic. If you slip a knife under it it pops off then the rest is a piece of cake. Maytag had no info on their web site and lots of other inaccurate info is posted on the web.

Turned off water suply. Removed drain (pipe is short). Then slid washer out so I could tilt it back and work under the washer. I put a wood brace under the front of the washer for safety. I then followed the instructions that came with the parts.

Removed the control panel, top and front panels to access the motor. Removed the motor and inspected. The motor looked fine. Leaned machine back and remove the brake cover following the directions posted by others on this website. Discovered grease and grime on the friction brake, which did not look right. The grease must have slung off of the transmission shaft. Wiped the brake clean with a dry rag and put machine back together. Machine did not run, motor only hummed. I replaced the motor only and the machine now works fine. My feeling is the grease caused the brake to stick and every time the motor started up, the sticking brake put a strain on the motor. Over time this cause the motor to burn up. Machine is only 6 years old. Sounds like a design flaw.

After examining the diagrams online, I removed the 3 screws holding on the back panel. Nothing seemed wrong so I tilted the machine to look underneath at the belt. All seemed OK but manually moving the belt by hand revealed that where the belt drives the pump had worn loose and was the source of the problem. Reading other descriptions of the ease of replacement of the pump, I ordered the new pump. It took approximately 15 minutes to remove the old pump and 10 minute to install the new pump and replace the belt. The machine is back to working fine. This is a fairly simple repair.

I first grasped the fabric softner dispenser and pulled it up and off agitator. I then removed the bolt from the center of the agitator with a 1/2" socket, 8" extension and ratchet. I grasped the agitator assembly and pulled it up and off. Reversed the procedure to install. The bolt can be started by placing a piece of paper towel over the socket, then inserting the bolt into the socket. It will hold it there while you start the bolt. I also took the opportunity to clean the accumulated soap scum from under the agitator while it was disassembled. An easy fix!!!