MAH9700AWW Maytag Washer - Instructions

My husband simply removed the old sensor and put the new one in. It was not difficult.

Installed dampners with a little trouble because of location on machine. But turned out not to be the problem. Machine still shakes and move. Looking for for another reason for shaking. Replacing dampners would be a "do it yourself project" for most people.

We followed another very helpful repair story. Unplug machine. Unscrew top back screws, remove top of washer. Reach inside from the top in the front of the machine. Remove screws holding latch in place, unplug the three plugs attached to latch. Replace with new door latch, screw it in place, replug the three plugs, put top of machine back on, replace screws on back and your'e done! Works great! Job made easy thanks to others helpfulness!

I ordered the pump because we have 3 kids and laundry piles up. The pump was not the issue, because it would drain in rinse, but not during spin... The computer would have been a $330 part. Not sure the issue, but my wife wanted a new dryer so we replaced the washer at the same time. I didn't use the part. The website was really easy to order and it got here fast.

Removed the broker door lever with screwdriver, installed the door lever with screwdriver. Took about 5 minutes.

this is a front load washer, removed a small access plate from the back of the washer, removed the old pump and install the new one

I had noticed the latch on door was split so I ordered the latch, but before I could put it on, the latch on the front of washer was locked. I then looked at the messages from others on this site for help. My daughter and I unscrewed the 2 screws on the top back, removed top, pulled the control panel up, unscrewed the front, unscrewed the 3 screws for latch, pulled old one out. I located the part, ordered it and got it in 2 days! Put new latch in and screwed everything back the way it was and in 15 minutes, the washer is running! (I am a woman too!)

The washer tech manual stated to: 1) remove the top, 2) control console, 3) front below the door (front load washer), 4) remove the retaining wire, 5) pull back the rubber bellows, 6) remove the three screws and remove the door latch/lock assembly. I discovered that steps 1 through 3 are not required to replace the assembly. Installation is the reverse of steps 4 through 6. That was easy. The difficult part was figuring out how to reset the pressure switch so the drain pump would not start every time you reconnected to the power supply (pressure switch thinks the washer still contains water). With the power disconnected, I disconnected the pressure switch from the central control unit. Then I reconnected the power supply and pressure switch. That reset the pressure switch solved the problem with the drain pump. Washer works fine now.

found diagrham on line, located parts needed , orded,replaced when arrived a few days later.

It is very easy. Unplug from the wall. Take out the two screws from the back that holds on the top panel. Unscrew the three screws inside the door by the latch. Reach inside the washer from the top and unplug the three plugs on the latch part. Then plug in the new part , put the three screws back in. Then put the top panel on. Plug in and magic. It works!

This took ten minutes .... super easy .... DO IT YOURSELF!!!! About 75.00 with shipping ... can only imagine this woulkd have been 250 to 300 to have somebody com e onsite.

Ordered new pump from Parts Select. Pump arrived within 2 days. Removed back cover off washer, 2 screws. Took 2 hoses off pump. Removed pump bracket and pump, 3 bolts. Took less than 2 minutes to remove old pump off bracket and replace new pump. Put everything back together and machine works great and water is out of clothes. Price of pump was the lowest I could find and I couldn't be happier with Parts Select quick response and price.

Coins sheared the impeller blades from the pump. I disconnected the power, removed the back panel, with pliers slide the hose clamp off the hose and remove hose...you will drain water from both hoses when removed (if washer is full of water be prepared for it all to drain)remove 2nd hose clamp and hose, with a 1/2 socket remove the 3 mounting bolts, and disconnect the power line from the pump remove old pump from mounting plate. Install new pump in reverse order.

My husband removed the water heater element. It was kinda an ordeal. Just glad it's done and fixed, relized how much I love to hate laundry.

I went to Maytag.com and typed in my model number and it came up with different parts I found the glass part I needed and ordered it. I received it in like 3 days. I had a phyllips screw driver and it the removal of the base around the glass replace the glass and screwed it right back on and started washing clothes. No leaks at all. I am a woman and proved woman can do the same things a man can do but quicker.LOL