Quick Question!

Have you ever purchased from PartSelect.com before?

Models > MAH6700AWW > Instructions

MAH6700AWW Maytag Washer - Instructions

All installation instructions for MAH6700AWW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the MAH6700AWW
31-45 of 92
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Water leaking down front of washer (6 o'clock position on the door)

  • Customer: Lucas from SAYLORSBURG, PA
  • Difficulty: Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 3 of 4 people found this instruction helpful
Started doing it following directions online, they all skip the hard part which is putting the boot back in. Gave up before damaging it and called professional. - If you want to do this repair you absolutely should remove the full front panel of the washer and be very patient. it will take a while if you aren't used to doing them. all the videos show performing this repair WITH the front panel on. DO NOT ATTEMPT THIS! Remove the front panel and install without it on!

door would not close on washer, had repair man to fix it $580.00 cost me $115. for parts ... thank u verrrry much

  • Customer: Richard from ELMA, NY
  • Difficulty: Very Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 2 people found this instruction helpful
so simple could not beleive .

Door would not close

  • Customer: Susan from ROCK HILL, SC
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 2 of 3 people found this instruction helpful
We watched the instructional video and it was a complete success!

Front door broken off hinge

  • Customer: Augie from BERKELEY, CA
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required:
  • 2 of 3 people found this instruction helpful
Unscrew all phillips head screws in the back of the door and the washer door will separate so that you can get the door off the hinge. Once you do that, you can remove the plastic gasket by depressing the area near the holder tabs gently (they will break if you're rough!). Put the plastic gasket in the new door cover and give a good whack on it over the tabs to make sure they go in. Before you put the glass holder on, take the hinges off from the washer. Once the screws are off, push the hinge up to get it out, then put it in the door cover/glass holder and screw everything back in. Now with the door and hinge together, put it back in the washer and then push down on the hinge to make sure the screw holes will line up. Put screws back in and done!

washer was making noise durning spin cycle

  • Customer: Peter from Roebling, NJ
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
  • 1 of 1 people found this instruction helpful
well had to take apart the whole machine to take out the drum, wasn't all that bad, Pulled out the inner tub , took apart the inner tub and behind the stainless tub was a spider arm which I did replace mine was cracked in 2 places. While inside the drum replaced the seal in the back of the tub since it was there for 10 years plus , Pulled out the old one , tapped in the new one and put all back together and now all is Great . ps do a lot of search of the part and you want pics of the item you are after, cheapest is not always the best also the serial number has something to do with some parts my machine had 2 listed for a series 10 and series 12, just make sure if a picture is available of the part it matches.

Drain pump would not pump out water

  • Customer: Gerald from DURHAM, NC
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Pliers, Screw drivers
  • 1 of 1 people found this instruction helpful
Installed new pump but washer still would not identify pump. Isolated pump with it's own power line and time the wash cycle to plug in the pump and drain the washer, if I miss the timing it goes to a trouble code and I cut off the washer and back on to set to the" rinse and spin" cycle to complete the wash. Not the best but am retired, the washer was given to me from a friend, and it works.

Washing machine wouldn't run. Kept making buzzing sound and didn't show door latched.

  • Customer: Keith from Amherst, OH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 2 of 5 people found this instruction helpful
Removed the 3 screws that hold the bottom front panel in place. Removed the 3 screws that hold the door latch in place and pulled out on the bottom of the door which wasn't very much and slid the door latch out to get to the wire connections. Connected the wires to the new latch and pulled out bottom again and put the latch back into place and put the 3 screws back in. Note: make sure you unplug the washer so you don't have a chance to get shocked. Level of difficulty was pretty easy.

broken latch

  • Customer: Hector from Richmond Hill, NY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 1 of 3 people found this instruction helpful
Unplug machine,remove three screws that hold on top cover.
Unplug latch switch assembly,then open front door of washing machine, remove three screws which hold latch
switch. Install in reverse order.

Close quaters to work on

  • Customer: Lanny D. from Clarksville, TN
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 1 of 5 people found this instruction helpful
I had to pull the washer out from the wall. SInce it is in front of the door going out into the garage made it dificult getting tools. I had to lay on my side doubled up in order toget to the hose. I used a bit extention so that I could get the clamp loose. Cut the time in half by using a drill with a phillips head screw bit. The only real hard part was getting the new one up tight on the drain. Used a heavy duty screw driver to push it up so the clamp would bite.

OE error. All i read indicated the need for new sensor, but it did not correct the problem.

  • Customer: LISA from PRINCETON, WV
  • Difficulty: A Bit Difficult
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 6 of 28 people found this instruction helpful
My husband simply removed the old sensor and put the new one in. It was not difficult.

shakining and moving

  • Customer: David from Manchester, NH
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Wrench set
  • 0 of 0 people found this instruction helpful
Installed dampners with a little trouble because of location on machine. But turned out not to be the problem. Machine still shakes and move. Looking for for another reason for shaking. Replacing dampners would be a "do it yourself project" for most people.

Washer flashed error code DL (door lock) and wouldn't start.

  • Customer: Marybeth from Warwick, RI
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
We followed another very helpful repair story. Unplug machine. Unscrew top back screws, remove top of washer. Reach inside from the top in the front of the machine. Remove screws holding latch in place, unplug the three plugs attached to latch. Replace with new door latch, screw it in place, replug the three plugs, put top of machine back on, replace screws on back and your'e done! Works great! Job made easy thanks to others helpfulness!

Error code nD not draining

  • Customer: Daniel from New Milford, CT
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Wrench (Adjustable)
  • 0 of 0 people found this instruction helpful
I ordered the pump because we have 3 kids and laundry piles up. The pump was not the issue, because it would drain in rinse, but not during spin... The computer would have been a $330 part. Not sure the issue, but my wife wanted a new dryer so we replaced the washer at the same time. I didn't use the part. The website was really easy to order and it got here fast.

Door lever was broken

  • Customer: Karen from Cincinnati, OH
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Removed the broker door lever with screwdriver, installed the door lever with screwdriver. Took about 5 minutes.

impeller destroyed, over worked the pump motor and burned it out

  • Customer: Dora from West palm beach, FL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
this is a front load washer, removed a small access plate from the back of the washer, removed the old pump and install the new one
All Instructions for the MAH6700AWW
31-45 of 92