MAH5500BWW Maytag Washer - Instructions

Followed instructions that came with replacement part, good as new!

I checked the power in with a line tester. The main line in had power and all five groups of lines going to the circuit board had power in each. The circuit board had been replaced about one year ago and there had been lights on on the touch pad when the circuit board was bad, so I guessed that the problem must be the touch pad itself. When I plugged in the new touch pad nothing happened. You have to wait 10-30 min for it to start working. I waited and when it finally came on, everything worked perfectly. Be sure to wait for it to come on.

Removed the door removed the hinges removed the screws holding the inner door in place removed all the parts under the inner door put everything back together in the opposit order from taking it out replaced the door wala! finished

I removed the rear access panel, used a nut driver and pliers to remove the old hose. I tried to connect the new hose with the spring clamp on the pump end of the hose. I gave up on that after a few attepmts because the clamp was very hard to manipulate with standard pliers. I used a standard screw type hose clamp (2") that I had instead. The tub end was easier because a standard hose clamp was used there already. The washer no longer leaks, and I saved a lot of money by doing the job myself!

1. ReMoved spring and cable from tub, 2. Remove bellow drain hose clamp at bottom of bellow, 3. Remove bellow from tub side and door frame, 4. Wet door frame with water and dish soap solution, 5. Press door frame side of bellow into slot. Align grooves, 6. slide tub side of bellow over tub edge, 7. Say a prayer to the good of your choice, 8. Reattach bellow cable with spring. This required use of double stands of 60lb braided fishing line to chinch most of the way and then use of a spring hook took in one hand and needle nose in the other. No less than 12 attempts. Be sure to have another pair of hands ready when doing and the whole job will take about 15 to 20 minutes.

Being a seventy five year old man I was reluctant to taking on this job but after getting prices for the repair or replacing the machine I cringed and trying to save some money I took on this job.Got all the information I could find on line I got started.Taking machine apart was easy and remembering to keep parts separated is something I learned from my mechanical back round is a must.Pictures also help.Taking out spinner drum easy.Bearings a nightmare If you don't have a bearing removal tool.Front bearing had to be cut out with a dremel tool and zip wheel being careful not to destroy the race.Removed spindel from spinner drum as I could see that for me to put shaft in hole would have been a problem.Put new improved seal in.Easy part.Reassembled. Springs and clips hard.Washing again and quiet.Wife happy four days later.Old guy sore.All done with outer tub in machine.Estimated savings Big,Big,Big.Getting big steak dinner and big kiss.

On-line instructions were found easily enough. And followed easily. Hard part was placing the cable and spring which secures bellow on drum. One instruction said "you cannot do this by yourself" (I couldn't see how help would have "helped") the other said "this was the hard part" of repair. I weight 115 lbs and it took me 1/2 hour to finally get the spring hooked through cable end it's a very STIFF spring! I only had a short pair of needle nose pliers - an 8-inch pair would have given me more leverage and shorten "hook-up" time.

My 16 yr old son replaced the door boot. He said it was very easy although the wire was alittle tricky. But all in all it was very easy for him. Saved me alot of money.

Removed front panels, lifted top to open position, removed back cover, removed drive belt, drum pulley, removed rear bearing snap ring, removed seal clips, removed 3 baffels then the 3 mount bolts. Pulled out spinner support and the inner drum. Removed the rear bearing #6206LL with brass drift rod and heavy hammer (came out with little effort. The front bearing #6207LL I soaked with penatrating oil overnight (this bearing was making all the noise as after 11 years water finally got to it) The next morning I had little trouble removing it with the brass rod and hammer, taking my time to work my way around driving it out. After cleaning everything up, assembly was the reverse, carefully driving in the new bearings. The new lip seal was the most difficult getting started without going in crooked. Time spent was a good 8 hours (it would have been more if the outer drum was removed) and the cost of everything was $167.09. Thanks to Part Select, the spinner support assy came the very next day. The two bearings came from Bearing Supply & Depot Inc. The washer operates like new!! Very Quiet!!

I went on your site and found out the Bearings were not sold separately by Maytag and that they wanted $800.00 for the entire outer tub in which the bearings are pressed into. I read another post on your site where someone referenced some NSK bearing part numbers. I went to my local auto parts store that cross referenced the NSK number to Timken Bearings (a high quality automotive bearing). Following the instructions I hammered out what was left of the old bearings cleaned everything and pressed in the new bearings. When the Lip Seal kit arrived I pressed in the new seal following the instructions provided, reassembled the washer and it’s as good as new. Total cost just over $100 in parts and a few hours labor. Removal of the old bearings was a difficult task especially since mine were in such bad condition as water must have been slowly leaking into them for some time. If you have some basic automotive repair skills and or some knowledge of how to remove and replaced pressed in bearings I would recommend this repair. In my case money was the motivating factor with 2 kids in college and a wife who would have insisted on a new matching set of a washer and a dryer instead of just replacing the washer.

I just followed what others have already noted. The only challenge was the spring as others have already stated many times. You will need help but be patient and you'll make it work.

Using online disassembly instructions removed and replaced front and rear bearings. Then attempted to install the seal kit that was purchased online from partselect. Com. Was supposed to receive both seals plus lubricant so that no matter which seal I needed I would be covered. The kit I received had 2 seals that were identical. . . I needed, as it turned out the early seal kit, but unfortuneatly I had 2 revised kits. Of course I tried to assemble one but it just won't work. The seal kit must be the correct one. I didn't give up. I ordered another seal kit online from appliance partspros. Com and received both kits as advertized. . . One being the early version plus a small packet of grease along with all the other required loose parts and was able to complete the repair. The second time around proved much easier because of the experience factor.

remove 4 dispencer screws I keep them in bleach cup. Remove 4 front panal screws. Remove front panal. Now with(5/16)nutdriver remove the top 2 screws. Lift and remove hold down bracket now lid will lift up. Inspect latch acembly take picther if necary to rember wire placement(note rout of yellow release cord)last 2 5/16 screws to remove latch attach wires and revers steps for a easy repair.

Followed the instructions that were supplied with the Lip Seal Kit, for removal of the inner drum. As expected, once into the project, I found that the bearings that are part of the outer drum, were bad. Reading other installation blogs, prior to starting, I knew the bearing sizes, 6206-2RS & 6207-2RS, and I purchased the bearings, from Motion Industries, before starting the project. Taking a hammer and long 1/2" socket extension I was able to remove both the inner and outer bearings form the outer drum. (Bearings were all but seized up) Once I had cleaned up the aluminum hub which is part of the outer drum and where the bearings mount, I was able to start the process of installing the new bearings and completing the project. Timing could not have been any better to take on this repair project because the aluminum hub was showing major signs of corrosion on the inner side of the hub. I was concerned that the new lip seal would not seal off the inner drum from the bearings/outer durm. This project was competed on 8/21/12 and so far and 6 loads later I have not found any leaks.

I opened the back of the washer, put the isolator in the hole it belongs in. I then inserted the motor pivot pins into the holes, and installed the motor bolt. Installed and tensioned the belt, tightened the motor bolt, and installed the back cover.