LTF6000ES1 Frigidaire Washer - Instructions

Unscrew the the bad part, screw on the new part

ordered the part and got the part in three day. A no hassle experience. Installed the latch and eureka! Fixed!

with the help of my nephew, we unstacked dryer after power sources were shutoff first. then simply removed the two screw attaching lid on washer. then removed two screws holding switch from front of machine. fished switch up to a visible area, exchanged bad for good. fed switch back to it's home,then reversed assembly procedures. these forums are great and have saved me money by enabling the repair both washer and dryer at a very reasonable cost without the need of a certified repair person.

Nothing to it rteall. The great thing was how fast this company got the part to me!

First I unplugged. The machine from the outlet then disconnected the two water supply lines from the machine. Next I removed the back panel to gain access to the bottom of the drum. Next I took a nut driver and used it to depress the little tab on the push pin that hold the bottom part of the strut on. After getting the pins out I replaced the old strut assembly withe the new one. I used the nut driver again. But this time I used it as a set tool. Place the nut driver on the end of the push pin and gently tap with a hammer. Until the pin is all the way in. After that I reversed the assembly process to put the machine back together.

before you buy any parts do this first..turn on your washing machine,then push and hold start and pause at the same time.An error code will come up,look in your book and see what that code represents. Mine came up 47.that error for my machine was the door switch.

The front loading washer door was wobbely so I took it apart as per wife request. Hinge looked fine, bushings were fine so I started to put it back together... then the glass slipped out and to the ground. Take the time to remove the door hinge and assemble on a flat surface, then place the whole assemble back on the washer machine. Don't try to take door apart while still attached to machine. Try it you will understand and then you will be buying a new glass front.

Got on line order the part from PartSelect. Got the part quick and the instructions was so easy my wife fixed it.

removed top of washer then removed the screws that held the lock in place. only hard part was the lack of room to slide my hand down to get the lock from inside the washer,and put the new one in. managed to find a tech sheet in the washer to put the washer in a "service mode" that is where i could make the washer do a final spin.but it still gave me a code that the door lock was not working properly.(even though it still locked)replaced the lock with a new one and the code disappeared and did a full final spin.. thanks guys

Had to take the front and back panel off the washer. A couple of clamps and electrical plug in came off and then the motor. Put the new motor on plugged it back in and put on the clamps put the panels back on and was able to wash a load of clothes. It is now quiet and spins the clothes out as if it was brand new.

I took off the broken part with a screw driver. I easily found the needed part on your website. After I ordered the part, it came within 2 days. It was the correct part and was replaced within 10 minutes of opening the package. Thanks for the great, easy and quick service!

After some research online about my Frigidaire Washer, I pre-determined that the problem could likely be the lock mechanism. I ordered the part and it arrived within 3 business days. My son removed the screws from the back of the washer, slid the top off and removed the old part and replaced it with the new part. It took about 20 mins. The machine is now working properly again. The door catch that I ordered did not work with the door lock I ordered. However, the old door catch that was still in good working order does work with the new door lock and switch assembly that I purchased.

Everything on the video was fine except when reinstalling the shocks with the plastic pins it was almost impossible to get a hammer back inside to knock in shock on left side and had a plastic part on the right side behind the shock absorber which you could not use a hammer and could pry on that part out of fear of damaging it when reinstalling pin So the video just said the right side just like the left but each side was different in what was located by each side Just confusing meaning you had to be creative in solving them!

I took the broken dispenser out, slide the new one in and rearrange the wiring. It took longer to move the washing machine from it's location and return it than it did for the repair. The key element it was the right part and fit properly.

Pulled off back panel and found that the Drain pump had some how came loose, so I found screws and tried but still wouldn't work check pump for blockage couldn't find and but could hear the pump hum so figured the pump went bad. the hardest part was getting the squeeze type clamps off or it would have been a 30 minute job. I orederd new part and it came fed ex next day and put in and changed the bellows clamp to worm gear and made it a lot easier going in. Started washer and ran just like it was supposed to.