LTF2112ARB Admiral Refrigerator - Instructions

Removed wiring from old ice maker and install on new. With 2 screws all ready in place hung ice maker on them. Attach wire connector into socket and install bottom screw to hold ice maker. Tighten top 2 screw and put wire guide in place. Drop wire guide down and ice started in 10 mins

Pulled the plug on the refrig. ( This is important since the heating bar on the bottom of the ice maker could come on as soon as you plug it in and burn your hand ). Removed the ice bin to get it out of the way and then removed the 1/4" hex screw from the support bracket under the old ice maker ( don't lose it ). Pushed up on the old ice maker to dislodge it from the 2 support clips on the top of the ice maker. Squeezed both sides of the wire harness plug and pulled it out and removed the old ice maker. Removed the wire harness and level bar from the old ice maker and installed them on the new ice maker. Plugged the ice maker wire harness into the female receptacle in the freezer. Popped the ice maker in to the top support clips making sure the rubber water chute from the refrig. was in place in the round ice maker receptacle. Plugged bak in the refrig. and I was getting ice in about 2 hours. Working fine after 1 week producing plenty of ice. RussK---

following the advice of this site, purchased a new ice maker. Old one was simple to unhook and remove and new one was just as easy to install. Within no time at all, I had ice being made and it has been working perfect since. Thank you for the help...

I followed your posted video. Did step by step as video instructed and in about 30 minutes finished. Ice was made approx 30 minutes later. I hope you do more videos, a picture is worth a thousand words.

I replaced the defrost heater and everything is working now! Thank You for the discount parts and information Fresno Ca.

Removed Ice bin, remove rails on left side that hold ice bin. Remove one screw holding ice maker to refrigerator wall,then lift ice maker off holding screws. Unplug wire harness from back of refrigerator. Remove wire harness and loading wire from old ice maker and install on new unit. Re-install new ice maker by reversing steps. Videos where very helpful.

Followed on line instructions. Instructions were very helpful. The part was an exact replacement. Everything went as planned.

Followed the Video, and it went almost as the video, except for the rails for the ice tub, so instead of the nut driver, had to use an open end 1/4" wrench. Now its a working with lots a ice....

I received the new icemaker the next day after I had ordered it. After watching the video on how to install the icemaker I installed it within a few minutes which I really surprised myself since this was my first repair job to do by myself. The new ice maker has been working great and I am very pleased with partselect and will continue to contact you when I am in need of any parts. Thank you, betty

1 removed ice basket 2 remove cover over basket 3 unplug power cord 4 loosen top screws with 1/4 in nut driver (do not remove the completely) 5 remove lower mounting screw ( not necessary to remove basket rail) 6 remove ice maker from unit 7 remove bale from old unit 8 install bale on new unit 9 remove front cover from old unit 10 remove power cord from old unit 11 plug in cord to new unit 12 install old front cover on new unit 13 mount unit in freezer 14 hang unit on top screws 15 install bottom screw 16 plug in unit 17 put in ice basket and cover. no runs, no drips, no errors. Ice was made in about 2 hours.

Fast delivery...Great video instructions..The only difficulty is when I tried to take the cable out. It's kind of hard and far away from my reach. So, I took only the cable out on Ice Maker end.

Unplug refrigerator, turned off water to ice maker, unscrewed bracket, lifted ice maker off clips, pulled out water hose,disconected wiring harness and lifted out old icemaker. Reversed the process and it worked like a breeze and no service call. Space is very tight and you have to do a lot of feeling without actually seeing what you're doing and you need a small flashlight. It was so easy with diagram provided on PartSelect's website.

Found PartsSelect on internet. Read data, watched remove/replace video, ordered new Ice Marker. Arrived in 11/2 days-quick. Both removel and install very easy; three easy to remove screws, disconnect wire harness pull it out. However, water cup on end of the new Ice Maker was faceing 90 degrees the wrong way! Had to totally disassemble both new and old Ice Makers to swap water cups. Reassemble, pray it was done correctly and install. New Ice Maker works like a champ and no leaking--Thanks PartsSelect.

The glass replacement piece just went right back into the frame perfectly. I didn't have to do anything special, I am really pleased with the fast service though. It shipped the same day I ordered it!

The icemaker in my Maytag refrigerator was having a few problems. First, a small leak developed in the ice cube tray, allowing water to drip into the ice bucket. This of course caused the ice to become one solid mass, totally inappropriate for a gin and tonic. After a couple of months of this, it stopped working altogether. On to the internet I went, and discovered how easy this repair actually was. One nut to remove, one to put it back in. The installation video was very helpful. I did have a concern at first because the icemaker did not start making ice rights away. I thought it might be a defective unit. It took about 12 hours to get the first batch and it has been happily cranking out the ice since! Ed in upstate New York.