Quick Question!

Have you ever purchased from PartSelect.com before?

Models > LRSC26925SW > Instructions

LRSC26925SW LG Refrigerator - Instructions

All installation instructions for LRSC26925SW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the LRSC26925SW
1-15 of 20
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Evaporator Fan Squeeking

  • Customer: Kyle from WOODBURY, MN
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Wrench (Adjustable)
  • 8 of 9 people found this instruction helpful
Detected noise as coming from top freezer department, and tips and part diagram clearly pointed to evaporator fan. You go in through the freezer (you have to empty top half of freezer); removing the side rails holding the ice bin, and then the 4 outer screws (only 2 each side - not the middle ones) holding the 'auger' that turns the bin. From there it gets interesting in trying to disconnect the wires. You might consider taking some pictures of the connected wires - perhaps it doesn't matter, but several of them can be hooked up in reverse. After the ice marker is out, remove light and light cover, side rails/mounts that hold hold up ice maker. This leaves a large white cover that pops out (seam at bottom of it has two tabs that you can pop out) holding the fan; and then only a few more wires to disconnect to be able to get at the fan. Mine clearly had a wobble to it confirming the source of the squeak and need to replace. Install was just reverse -- a bit tricky to get some of the wires connected given the tight spaces. Overall, not difficult - but a lot of wires and screws to connect/disconnect. I didn't take any pictures as I disassembled, and found myself having to take some extra time to figure it out as I reassembled. In the end -- a silent and functioning refrigerator Good luck!

Water Line from filter to water valve leaking.

  • Customer: Brannon from SAN ANTONIO, TX
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Wrench (Adjustable)
  • 3 of 3 people found this instruction helpful
1. Remove the filter - 1 screw at top of filter and pull-out. 2. Use crescent wrench to push down at tube inlet and pull tube out. 3. Remove bottom screen from refrigerator. 4. Use crescent wrench to push down on water inlet and pull out tube. 5. Route new line on back of refrigerator. 6. Install is the reverse of removal. Thanks.

Ice dispenser door didn't close

  • Customer: Wesley from WILTON, NH
  • Difficulty: Very Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 3 people found this instruction helpful
I replaced solenoid, flapper heated door, and broken spring. Very easy instructions on "YouTube"

My ice maker overflowed water and made a mess in the freezer

  • Customer: steve from clarence center, NY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
The part was extremely easy to replace. The unit came out with one screw, and I had to unplug the wire connection. After removing I noticed the ice tray was cracked - that's what caused the problem. The new unit went in easily with 1 plug in connection and 1 screw. I was done in less than 10 minutes.

Rails broke when overloaded

  • Customer: James from Bremerton, WA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Removed shelf that rails were mounted to. Used a std phillips screwdriver to loosen screws attaching the rails, three per side. Removed damaged rails, lined up new rails and tightened screws. Returned shelf to refrigerator and inserted tray on the new rails.

Both guide rails had cracked at the front end I guess do to excessive weight in the drawer.

  • Customer: Robert from Parkland, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Simply removed the drawer, then removed the shelf above which held the guides, removed the guides ( 3 screws per side )and replaced them.

entire ice maker unit broken

  • Customer: MARCUS from ALEXANDER CITY, AL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I replaced the ice maker assembly and the ice container auger assembly. Installation was fast,considering that I was able to look at how the old unit was installed and simply copied what I saw. The parts were the exact same which made installation easy. There was only one screw that needed to be removed inorder to take the old unit out. The new unit is easily put back in it's place, and the one screw put back in. This was the quickest and easiest, "do it yourself" job, that I have ever done. Thanks for everything Part select.

Two Door baskets were broken

  • Customer: Jill from Burleson, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
We had two of the door baskets break and so we had no room in the frig. My husband and I were talking about maybe just replacing the frig. He said lets see if we can find the parts online. So we came to this site, found our parts, ordered. Received very fast and installed seconds. Saved money on buying a new frig.

refrigerator light stayed on when door was closed & heat from lights melted plasted parts

  • Customer: Barry from Baton Rouge, LA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
replaced both push button lights (french doors on refrigerator) and replaced plastic parts on overhead lights (note: ordered/or was sent wrong type pushbutton light switches - with one phone call was reinbursed cost of these switches & was sent correct switches 3 days later) with no hassle

Ice cubes did not drop out of tray when the ice maker cycled

  • Customer: Michael from Eagle, WI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
1) Take out 3 screws from top of icemaker. 2) Unplug electrical connector from wiring harness. 3) Remove icemaker unit from freezer and then remove frozen cube sensor with clip and rear insulation. 4) With your hands pull cube tray motor out of the holding clips with the tray- if this is too difficult, spread bracket and only remove the tray from the unit. 5) Insert new tray into slots and install new or existing ice sensor, insulation, and sensor clip. 6) Reinstall icemaker unit to ceiling of freezer, don't forget to plug into wiring harness. 7) Turn unit on and make some ice!

Manufacturer Cahnged Part Desin

  • Customer: David from Lewisville, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Not the fault of partselect. The manufacturer had decided to modify my part and still specifying that it was the NEW part number and that it was the direct replacement (shame on LG). Well its not the same part. The partselect CSR worked with me to try and find the previous design to no avail, even going so far as to give me the phone number of an obsolete parts seller... wow! Without a whimper parts select credited my account for the part that would not fit!! Without a doubt I will use them again. Way to stand behind your sale!! And also I got the parts within two days, amazing. The ones that did fit were well packed in perfect condition and on time. DON'T HESITATE TO USE THIS COMPANY

Water and Ice dispensing just stopped working. Also Ice trap was broken.

  • Customer: BRENT from Glendale, AZ
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Wrench (Adjustable)
  • 0 of 0 people found this instruction helpful
Water valve replacement at back bottom right. Removed, water supply line and old valve with 1 screw and removed clips from hoses. Replaced with new valve and re-clipped hoses. Easy fix! Cleaned coils and back with blower and vacuum cleaner while I was in there too. I also had leak in water supply line, replaced. Ice trap door replacement was a little more challenging. Hard to get off the ice dispenser funnel (Part# 278D). Has 4 lock clips on it and 1 broke when I took it off. This part# 278D is not available from part select?? Tricky to replace the trap door itself. Have to make sure the door valve sits in solenoid correctly. Installed wrong the first time and door would not open/close. Had to go in and reset orrectly. Works like a charm now. Still need part# 278D!!

Each time we've had to move we have to remove the doors from the fridge to get it thru the front door.since water and ice run thru the freezer door there are 2 tubes that connect at the bottom of the freezer door that aren't meant to be separated very often if ever.it's easier to cut the tubing on b

  • Customer: Sarah from Elk Grove, CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
With alot of elbow grease and a pair of pliars we managed to get the old connector off wo cuttig the tubing as the tubing was getting to short from being cut once to many times & there was no more play in the length.Original connector was a different color and shapped slightly different than the new one so was a bit concerned that I had ordered the wrong part but it went one very easily & did not leak. We even managed to remove it again just to see if it was possible wo cutting again. it came off with no trouble.I would say the replacement part was a better fit than the original simply because we could remove it easily wo having to cut the tube!

Broken ice auger

  • Customer: David from Katy, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
New part fit perfectly.

The rails for our cheese drawer broke

  • Customer: wendy from west chester, PA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Just unscrew screws from old rails (still in refridgerator ), and screw them into new rails. We tried to order these parts from another online part site and we got the wrong parts. Partselect.com had drawing of our fridge and it was very easy to navigate through the web site. Thank you!
All Instructions for the LRSC26925SW
1-15 of 20