Quick Question!

Have you ever purchased from PartSelect.com before?

Models > LRFC25750TT > Instructions

LRFC25750TT (ATICLGA) LG Refrigerator - Instructions

All installation instructions for LRFC25750TT parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the LRFC25750TT
1-15 of 53
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Remove and replace light switch

  • Customer: Debbie from Waltham, MA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 18 of 27 people found this instruction helpful
Video makes it look easy. Kenmore refrigerator does not have "groove" along the right hand side of switch that allows for pushing down on release. Used a thin screwdriver to get under to push while holding switch edge with pliers. Kept slipping. Tape sides to avoid scratching inside of refrigerator.

Replace Thermistor in back of freezer

  • Customer: Scott from JUPITER, FL
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers
  • 4 of 5 people found this instruction helpful
Turn off power, remove upper and lower drawers (may need to open upper refrigerator doors to remove large freezer bin,) remove drawer supports (upper and lower), remove rear freezer panel (trick is to loosen 4 screws on fan bumpout to get the panel to come free from the freezer side wall), test thermistor with multimeter (should have continuity or near zero resistance across 2 orange fuse wires) before cutting zip ties, cut zip ties holding Thermistor in place, remove old Thermistor, install new Thermistor, install new zip ties, replace rear freezer panel, install upper and lower drawer supports, install drawers, turn on power, should be fixed if error code doesn't return after 6 hours.

Freezer Drawer door would not close easily due to worn / damaged sliding rails

  • Customer: James from SURPRISE, AZ
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Wrench set
  • 2 of 2 people found this instruction helpful
Removed the large freezer drawer bin. Took out the 2 screws holding the door to the rail, pulled drawer off the rails and set it aside. Note: the drawer still has the non-sliding part of the rail assembly attached to it. Reached inside the freezer and pushed the tab holding each of the rails and slide out the old rails. Removed the bolts on the freezer door holding the remaining part of the rail assembly (The white part). Attached the complete rail assembly to each side of the freezer drawer. Inserted the drawer and newly attached rails into the slots holding the rail. Slid the drawer in which allowed the rails to slide over the holding tabs. Checked door for in / out sliding easy and inserted the large bin back into the unit. I had purchased the full L & R rail assembly.

Fridge light would not come on.

  • Customer: Grace from GALLOWAY, NJ
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 2 of 3 people found this instruction helpful
After watching a few iTunes videos I was able to order the light switch from part select and within a week I had the new switch. I had a little trouble getting the switch out. I used a flat screw driver and taped around the edge to keep from damaging the wall inside. I found the clip on the right side and had to use some force to get it popped out, you may need to use pliers to disconnect the switch.

Replace the light switch for the refrigerator

  • Customer: Karyn from DURHAM, NH
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 1 people found this instruction helpful
Cover the putty knife with tape so you do not scratch the side wall where the switch is located. Slide the knife under the edge of the switch and push in a bit towards the switch and slightly twist to pop the switch out of its hole. Disconnect the wires from the switch and simply plug in the new switch. Push wiring back into the hole and careful push the switch into the hole until it snaps into place.

Light quit coming on when door opened.

  • Customer: Calvin from Northome, MN
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
Unplug from wall receptacle. Pry switch out with screwdriver while pushing on inner tab. Then disconnect electrical plug.

Refrigerator light had a short in it and would randomly work

  • Customer: Tammy from HAGERSTOWN, MD
  • Difficulty: Very Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
Unplugged the fridge. Used a screwdriver to loosen the switch. Easy to disconnect from fridge and just plugged the new switch in. Popped right back into the side of the fridge and worked perfectly.

the light did not work when door was opened. At first it would flicker then off completely.

  • Customer: Alma from Winterport, ME
  • Difficulty: Very Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
My son just pried out the old switch with a screw driver snapped out the old one and snapped in the new one. Pretty sure even I could have done this. Very quick and easy. Thanks. :-)

The switch became intermittent - Possibly a poor designe

  • Customer: Sidney from ENDICOTT, NY
  • Difficulty: Very Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
Used a small screw driver inserted into the front of the switch (facing the front) and pried until the switch was coming out. When out, I removed the connect harness and replace the switch with a new one.

icemaker quit

  • Customer: marvin from montgomery, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Wrench (Adjustable)
  • 8 of 26 people found this instruction helpful
i first replaced valve as the water line hung up and broke the valve as i was moving fridge out,be careful about doing this,now i need to replace icemaker as its not working,ps it wasnt the water valve ,i broke it,so first replaced it now icemaker ,lg stinks for the 2 yrs icemaker has worked,my previous kenmore icemaker thru door worked for 23 yrs and was working the day i replaced it, the new electronic appliances are nice when they work!!!>Marvin

broken

  • Customer: william from mashpee, MA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
removed 1 screw and replaced

broken part

  • Customer: Lisa from Santa Fe, NM
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
replace piece

I recently cleaned my sister's lg fridge and broke a crisper drawer

  • Customer: John from Apopka, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
My sis is disabled and not able to to house work, so I helped out by taking apart the LG fridge to clean it and broke a crisper drawer front. I ordered the part about 2 PM on Wenesday and the part was delivered before 11 AM. It took all of one minute to fix and boy was she happy. Thanks for being so efficent and responisve.

Broken Crisper Drawer Door Holder Clip (Small Plastic Hinge On Door Required New Door To Fix)

  • Customer: Thomas from Olympia, WA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I actually glued the item the first time repair was needed - lasted over one year. After it broke again; ordered the part from lg on line; and three days later the part arrived and repair complete. Also, I bought an extra door should the other crisper door fail. These doors and other small white plastic parts are seemingly prone to breakage. I am not rough on my appliances, yet I have had one or two other failues of interior parts. Very happy with lg, nevertheless.

crisper drawer door broke

  • Customer: Gary from Olympia, WA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Just searched online, found PartSelect, ordered the part, replaced it. Perfect
All Instructions for the LRFC25750TT
1-15 of 53