Quick Question!

Have you ever purchased from PartSelect.com before?

Models > LNC6766A71 > Instructions

LNC6766A71 Admiral Washer - Instructions

All installation instructions for LNC6766A71 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the LNC6766A71
256-270 of 387
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

loud noise on rinse & spin cycle

  • Customer: Betsy from Van Buren Point, NY
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Removed back inspection cover which was two screws,the pump with pully was right there. Removed the belt and three screws from the pully and pulled it out. Put new pully in tightened the three screws put the belt back on and the inspection cover plugged the machine back in turned it on and it ran perfect.

Lid hinge was broken on the washer lid

  • Customer: max from Plymouth, MI
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I followed the instructions on your video - it was very helpful! I would have never figured out how to take the top off without the video instructions. I released the top latches using the putty knife, removed the broken lid hinge & pin and installed the new ones.

Broken Lid Hinge Pin

  • Customer: Matthew from Gilbert, AZ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Took off the lid unscrewed 4 screws and replaced with new parts. Very simple.

machine would walk across floor & shake vilently

  • Customer: William from Hayesville, NC
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Repair went as described in instructions supplied and YouTube Video "snubber ring". I could not have removed tub springs without putting 72 quarters in springs before removing as seen in another repair video which made removal and reinstallation doable. I still don't understand how this inexpensive part can cause such a problem.

Agitator stop working and water leak

  • Customer: Anthony from Fairfield, CA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
To simple the agitator one socket three minutes done. Water leak took longer because we had to move out the washer and took off the back with nut driver and a pair pliers done. Thank you for your incites.

Water leak into tub and inside of machine, onto floor.

  • Customer: Steven from Lompoc, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
There was a crack in the black rubber hose attached to the water inlet flume assembly, and the assembly itself was cracked and falling apart. 1) Turned off water. 2) Lifted top cover up (pry up with flat screwdriver). 3) Disconnected hose. 4) Trimmed hose above the crack. 5) Replaced "spring" -type hose clamp with small automotive-style clamp. 6) Unbolted flume from under lid (2 sheetmetal screws). 7) Reattached hose to new flume. 8) Reattached flume to underside of lid. 9) Closed lid (light pressure downward required). 10) Turned on water. Total repair time: 10 minutes.

My Water Valve Replacement

  • Customer: daniel from cropseyville, NY
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
First piece of advice is to do all the work from the top; meaning un-hinge the top of the washer, do not disconnect any wiring to the washer controls, just the wiring to the water valve itself and kind of lay the top to the side a little. I initially took the small access cover off on the bottom, and tried to reach from the bottom, awkward and near impossible to get both hands in to where you need to make the repair. The rest of the repair is cake. Disconnect the wiring, disconnect the water supply line for the tub, replace the water valve and just work in reverse. :)

Broken water inlet valve

  • Customer: Gregory from Urbana, OH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
In our case, the hot water inlet valve was obviously broken. We picked up the washer on the side of the road in our neighborhood. We checked it out in our driveway - hooking it up to the water hose. When we connected to the hot side, water came gushing out the valve, inside the washer. A quick look confirmed it was obvioulsy broken. We connected the cold side and it started to fill the tub. Other checks confirmed the washer timer and other controls worked OK. we ordered the valve part from PartSelect (about $60 total). Took all of about 30 minutes to pull the old valave out and install the new one. Cleaned up the washer (it really needed it BADLY), and the washer is working perfectly now.

Washer wouldn't spin.

  • Customer: Charles from Sherrodsville, OH
  • Difficulty: Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
After reading several online posts about this problem on appliance forums and following the suggestions about how to determine what was needed (whether the inner tub turned freely (by hand) in spin mode or not. It didn't which apparently indicates the likely need for a new thrust bearing. I purchased the transmission pulley and bearing kit from Parts Select. I got it the next day, without asking for next day delivery! When I took the old parts off (easy: pull off the plastic cover, remove the circlip and everything falls off the shaft (if you are working with the washer just tipped up. Unfortunately, that was where my easy repair ended. The parts were entirely different! After looking and looking and thinking, I called Parts Select. They informed me that Whirpool, who makes Maytag had redesigned the parts. They didn't look like they would work, but I followed the directions which came with the kit and installed the new parts - three times. The last time the pulley stayed on and the washer spun as it ought. The problem was that even with the smaller of the spacer washers the circlip was extremely difficult to get in its slot. Anyway, now the washer works and I am pleased, even though I spent many hours on what ought to have taken perhaps 1/2 hour.

machine locked up

  • Customer: Fred from Batavia, OH
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Socket set
  • 0 of 0 people found this instruction helpful
removed belt motor and tub would turn and pump would not. ordered new pump removed three screws removed pump and reinstalled. washer works like new

Lid hinge on right side broken, lid hinge pin broken on left side

  • Customer: Layne from Waynesboro, VA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Watched video , after that there was no problem, really easy.

washing machine shakes and moves during spin cycle

  • Customer: Erich from Sheffield Village, OH
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set, Wrench set
  • 0 of 0 people found this instruction helpful
Had no problems taking machine apart following online instructions. At first couldn't find snubber ring because it was completely worn away. Once found it was very easy to replace. Only problem with putting back together was getting the first spring back on, after that it was a breeze. Machine up and running.

Won't Agitate, Won't Spin, Jumping around, squealing in spin cycle, abrupt stop

  • Customer: Gina from Los Angeles, CA
  • Difficulty: Really Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Washer was jumping around in the spin cycle to the point that it disengaged the water fill level hose which in turn caused it to overflow. I fixed the hose but almost immediateley it stopped spiining or agitating. I looked online to find that the jumping around was most likely the snubber ring ... the hard stop and squeal most likely the Brake Stator ... the no agitaion or spin was likeley the thrust bearing. I ordered the parts and were received in a couple of days ... by the time they came I had already torn apart everything and was just waiting on parts for reassembly. The instructions were concise and complete but I did benefit from watching a YouTube video on the repair. All the parts went together just like they were supposed to even with my limited mechanical skills. All I really used was a small socket set, a couple of screw drivers and a pair of pliers. Taking the Brake assembply is dangerous but can be done with no special tools if you buy a couple of 2 inch 10-24 screws to replace two of the short ones and then back them out slowly (look for a youtube video on this procedure EASY!) ... took me a couple of hours but any one who has used a screw driver more than once could probably do it in under an hour. Washer now running like new ... No Jumping!!! People at Parts Select were Great!!! BTW ... So that the springs would be easier to re-install, I stuck about $50 of quarteres between the coils before removing ... worked Great!

Broken hinge pin

  • Customer: Edwin from Bloomingdale, IL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
The repair was easy. 5 minutes after grabbing my tools the job was done. It was easy to find the part I needed on the web site.

alot of noise when spinning

  • Customer: Kathleen from High Point, NC
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Socket set
  • 0 of 0 people found this instruction helpful
..watched the video..easy as pie..took longer to figure out what part was making noise than to fix..
All Instructions for the LNC6766A71
256-270 of 387