Quick Question!

Have you ever purchased from PartSelect.com before?

Models > LNC6762B71 > Instructions

LNC6762B71 Admiral Washer - Instructions

All installation instructions for LNC6762B71 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the LNC6762B71
451-465 of 617
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Machine out of balance; banging; hopping.

  • Customer: Gary from Wellington, FL
  • Difficulty: Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Followed very detailed instructions posted on the website. Made a difficult job possible; without instructions would not have been to do repair. Thanks to those who posted step-by-step process. Suspension springs most difficult part of job, followed by C clamp. Lots of sharp edges to cut and scrape your arms and hands. After seeing how this machine is built, I am done with Maytag appliances.

Washer was off balance

  • Customer: Daniel from Fort Walton Beach, FL
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Cause:The main problem was the snubber ring got destroyed from continuously overloading the washer. That lead to the unit becoming off balance which in turn broke the belt pully off of the water pump and wore out the tub springs. Solution: Procedure 1: Make sure to turn off the water going to the machine, unplug the hoses and the power cord and if you have room take it out away from the wall. even after it is drained there will still be some water in the unit so keep a good size towel on hand. The pump is the easiest part to replace; simply lay the machine forward so that you can get to the back panel and the bottom at the same time. Remove the panel and the pump is just inside. remove the belt from the bottom of the unit then remove the black hoses from the pump taking note how they are situated and the size difference. Remove the bolts that attach the pump to the housing then lift the pump out through the opening; unless you have purchased new bolts you are going to want the old ones for the reinstall since the new pump probably doesn't come with any. Also, the replacement pump may not have the same mounting bracket but it will mount just fine without it. now simply install your new pump in the same position as the old, secure it to the housing and reattach the belt. Procedure 2: Now for the springs; this is a little more difficult and it is going to take some muscle and patience. Do not remove all of the springs at once, trust me! lol! The easiest way to do this is to remove one spring at a time and replace it with a new one; just make sure to mark them as you go or at least remember where you started. Only a few of them are accessible from the panel in the rear but if you tilt the machine back upright the whole front of the machine can be removed very easily. First you must remove the top; to do this there are two brackets on the back at the top behind the instrument panel that can be removed with a Phillips head screw driver. after they are removed pry the front of the whole top panel up, there are only two brackets holding it down. Remove the two screws that you have uncovered at the front and remove the front panel by lifting up slightly and pulling forward. you can now get to the rest of the springs. Take note how everything was removed and reverse process to put it all back together. Thanks and goodluck!

during certain wash cycles their was a burning rubber smell.

  • Customer: Jeff from Cornelius, NC
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
lifted the front of the washer on a 45% angle,leaned it against the wall and gained access to the bottom and the belt,rolled the old belt off,it was very stretched came off easily,rolled the new one on and that was it.

The problems only put the Belt in back

  • Customer: Syed from Mcallen, TX
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Wrench set
  • 0 of 0 people found this instruction helpful
The water pumps was was very easy to put it back in and I Save money And they have a video instruction to put it back in water pump This is a first time I repair something myself Everything was very helpful :)

Lid Would Not Stay Up

  • Customer: michael from blanchester, OH
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Took of lid,took out screws,put on hinge and pins,simple job

Agitator Broken

  • Customer: Barry from Spartanburg, SC
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
Replaced agitator in less than 30 minutes with ratchet and socket. Fast delivery from vendor. We are up and running again!! Very pleased.

The drain pump pulley broke and burnt the drive belt

  • Customer: Louis from Dozier, AL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
all I did was take the back panel off unhook the hoses from the drain pump and took the screw out the drain pump replace it with the new one put it back together,and roll the drive belt onto the pulleys and started it up and it work just like a brand new one. also run very quiet since i replaced the drive belt also.

loud noise when spinning

  • Customer: Brian from Allison Park, PA
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers, Socket set, Wrench (Adjustable)
  • 0 of 0 people found this instruction helpful
The video is really helpful. The clamps on one of the hoses slowed me down. It took some contorting to get the clamps compressed and at the right angle to secure the hose. My lack of patience was probably the culprit. FYI: My failed pump made no grinding sounds. Nor was there any resistance when turning the pulley. But the problem was indeed the pump. Working well now.

Loud noise during wash and spin cycles

  • Customer: Alex from Philadelphia, PA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Socket set, Wrench (Adjustable)
  • 0 of 0 people found this instruction helpful
I used the Instant-Repairman tool on the site to help identify the problem. It said I needed a new Drain Pump, I purchased it and a new belt which was not recommended but I figured couldn't hurt. Then I removed the belt from 3 pulleys on bottom of machine. Next I removed the access panel from back of machine. Then I disconnected both hoses from drain pump and removed it from washer by loosening the 3 machine screws. I installed the new drain pump with the 3 machine screws and reattached both hoses to new drain pump. I re installed the access panel and re installed the belt over 3 pulleys on bottom of machine. Presto - no loud noises.

Washer was squealing when agitating & spinning

  • Customer: Jan from Phoenix, AZ
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
All that had to be done was pull the washer out from the wall, tilt it back and roll the belt off one of the three pulleys and it fell right off of the other two. To install the new belt place it around two of the pulleys and roll it over the edge of the last one. Actually took 15 seconds to change it. Getting the washer out and ready took the most time. Now there is NO noises when it agitates or spins. LOVE IT!

A periodic loud noise during the Spin cycles

  • Customer: Randy from Phoenix, AZ
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Socket set
  • 0 of 0 people found this instruction helpful
This is a quick and easy repair. Start by using the putty kiife to depress and unlock the washer top. Remove the front panel of the washer by removing the two screws on eithe side at the top. The front panel then lifts off. Next you will want to tilt the unit up and remove the fan belt. Put the washer back down flush and remove the hoses to the drain pump located at the front an right side of the bottom plate. Once the hoses are removed you can remove the three retnetion screws, take the pump out, put the new pump in and fianlly replace the rentention screws and hoses. Put everything back together in reverse order and don't forget the fan belt. Takes all of 15 minutes of your time and you save 150 dollars labor.

noise sound,very loud while running in all cycles.

  • Customer: Thomas F. from Lady Lake, FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Socket set
  • 0 of 0 people found this instruction helpful
view video on how to remove belts, motor and water pump. I follow the instruction given. the video is very helpful, gave me all I needed to do the job myself. thanks tom

My machine was wildly out of balance

  • Customer: Paul from Charleston, SC
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
  • 0 of 0 people found this instruction helpful
I followed the online video on the Partselect website to replace the snubber ring on my Maytag Washing Machine. It was a very good video. The video had the same exact model even. The gentleman on the video was awesome! This is my second time using Partselect for a DIY job. I fixed my dryer a few years ago by watching one of your videos and purchasing your parts. I will never call a local repair company again. Half the time the don't even show up and then they charge you an exorbitant markup on the parts, not to mention the labor costs. Of course they never have the part in stock and they always have to order it. I did call around my hometown to different places that sell appliance parts... The all said they would have to order the snubber ring ... none had it in stock. So, I bought the parts from Partselect.com, had them shipped overnight and still saved a bunch of money. After I installed the parts, my machine runs perfectly! It has been about two weeks now and it has not been out of balance a single time. I will definitely be a return customer and I will highly recommend your website to all my friends. Thank you!

Lid hinge pin broke

  • Customer: Paul from Antioch, TN
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
The videos included in the shipping notification email made the repair a breeze. The only thing not shown was (at least on my washer) that the screws that needed to be removed had torex heads instead of normal slot or phillips heads. Luckily my tool crib had what I needed.

bearings ground to a halt

  • Customer: edward from dunedin, FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Wrench set
  • 0 of 0 people found this instruction helpful
Disconnected in and out hoses. Unscrewed part, screwed in new, reconnected hoses, installed belt and cover panel. Stood up the machine and tested. Good to go.
All Instructions for the LNC6762B71
451-465 of 617