LNC6762B71 Admiral Washer - Instructions

Removed the control panel, top and front panels to access the motor. Removed the motor and inspected. The motor looked fine. Leaned machine back and remove the brake cover following the directions posted by others on this website. Discovered grease and grime on the friction brake, which did not look right. The grease must have slung off of the transmission shaft. Wiped the brake clean with a dry rag and put machine back together. Machine did not run, motor only hummed. I replaced the motor only and the machine now works fine. My feeling is the grease caused the brake to stick and every time the motor started up, the sticking brake put a strain on the motor. Over time this cause the motor to burn up. Machine is only 6 years old. Sounds like a design flaw.

After examining the diagrams online, I removed the 3 screws holding on the back panel. Nothing seemed wrong so I tilted the machine to look underneath at the belt. All seemed OK but manually moving the belt by hand revealed that where the belt drives the pump had worn loose and was the source of the problem. Reading other descriptions of the ease of replacement of the pump, I ordered the new pump. It took approximately 15 minutes to remove the old pump and 10 minute to install the new pump and replace the belt. The machine is back to working fine. This is a fairly simple repair.

Removed the 2 screws on the front panel after unplugging the unit. Removed the 2 screws on the safety cover and removed the wiring coupling. Removed the 2 bolts that was holding down the belt adjuster. Fed adjuster around pully wheel after removing belt. Installed new motor and re-assembled in reverse of disassembly. Plugged in unit and tested motor. Unit still operating satisfactory. Wash about 5 loads everyday. Large family

After using my existing parts for about 6 months, and constantly having to tighten the bolt, I though that the parts might be stripped. It took one minute to unscrew the bolt that holds the two parts of the agitator together with a socket and 10" extension. After taking those parts off, it took another minute to put the pieces back and screw the new bolt back in place. Extremely easy - and much less expensive then having a repairman come out to fix it.

Remove the access panel at the back of the machine. Locate the Motor Pivot Spring. It is about the same diameter as a coat hanger and is attached to the motor and the motor base. I was able to remove the old spring and install the new spring with my fingers. When removing the old spring, remove the motor end first, then the motor base end. When installing the new spring, attach the motor base end first, then the motor end.

Removed laundry softener dispenser, removed bolt with socket wrench and long extension, pulled off old assembly piece, installed new assembly and replaced bolt. It took longer to order the part than to replace it!

Opened the front panel by using a flathead screwdriver (to pop the top lid up) and socket wrench (to loosen the front panel off). I then had to reach in and replace the missing/broken suspension spring. The spring was very difficult to extend so I used coins to lodge into the spring to elongate it. After the spring coils were loaded and held apart with coins (nickels and quarters) the spring could be installed using a pliers for leverage. The washer doesn't make the loud banging noise anymore!

Tipped machine 45-degrees to reveal belt on bottom of machine. Used screwdriver to remove old belt which looked fine. Installed new belt (which arrived from PartSelect within 2-days) but it felt loose. Tried machine anyway and it works just fine. Easiest repair ever. Thanks, PartSelect!

I used a putty knife to disengage the clips that attach the top of the washer to the front panel. The top will lay back without having to hold it however, I didn't trust it to stay up on it's own so I used a bungy cord and straped it onto a wire rack that hangs on the wall above my washer. Next I removed the two screws, one on each side, located on the inside of the front panel near the top of it. Then I gently pulled the front panel towards myself so that I could lift it off of the clips located at the bottom of the panel. The pump assembly is located at the front right corner inside of the washer. I disconnected the two hoses that run to the pump assembly and using my ratchet, I removed the 3 screws that hold the pump assembly in place. There is a belt on the bottom of the washer that goes around three pulleys, one of which is the pump assembly pulley. After I removed the pump assembly, I took the belt and laid it to the side. I then installed the new pump assembly. After I put everything back together, I gently tipped the washer over on it's side as far as I could and reinstalled the belt around all three pulleys. I started with the pulley on the left side and then the pulley in the middle and finally, the pump assembly pulley. I have washed a total of seven loads of laundry since I did the repair and have had no problems.

I checked out your other repair information and deided I could do this. Ordered the part and it as her several days before I expected it.

Ok, let's do this thing.

MAGIC TOOLS:
5/16" socket or wrench and #2 Phillips screwdriver and something to remove hose clamps - I recomend a 6" to 8" vice grips and a 6" to 8" plires.

1. Pulled the washer out in the middle of the floor and disconnected the hoses and removed the rear access cover, disconnected the pump hose, released the top using a 1/8' common screwdriver in that narrow space between the top and the front panel. Removed the 2 screws holding the front panel on and removed the front panel.

2. Disconnected fill level hose- toward the left rear side - turned the machine on it's side and walked the drive belt off, tipped it back up right and removed the 6 springs - be sure to note their orientation and location.

3. Lifted the whole assembly out of the top of the machine and set it upside down next to the machine.

4. Loosened the screws holding the snubber in place - NOTE I did not remove the screws - loosen them sequentially little by little untill you can get the snubber to come out. I did not remove the pulley as my Craftsman ratchet and standard - short - socket allowed me to get between the pulley and the screws to loosen them.

5. I removed the old well worn snubber, cleaned the area up and the new snubber actually fell into place and I retightened the screws in the reverse order until they were solid feeling.

6. I lifted the assembly back into the frame, reconnected the springs and the pump hose and the fill level hose. I reinstalled the front cover - AND HERE IS THE IMPORTANT PART!

7. You are so happy this is going so well that you forget to put the BELT back on before you hook up the hoses, so you have to unhook the hoses to put the belt back on and then rehook the hot and cold hoses and drain hose again.

8. Except for number 7 this is a piece of cake. My only concern is how often will I have to do this. The machine is only 8 years old.

Move washer to area with plenty of room. I took mine out to the deck. take off front of cabinet remove back panel, remove old springs, (a bit hard) remove belt, lift out tub turn over and loosen screws do not remove!! remove old snubber and replace with new, Not bad. Put tub back in washer put on new springs(didn't think I'd ever get them on, not enough upperbody strength)Video would have been priceless!
reattach belt and panels put washer back in place. No noise upon spinning but I now have issues with the agitator, Need a new washer!

Opened the top of the washing machine, removed the two screws and the front cover removed the agitater, drum and outer tub. replaced the bearing and seals and reassembled.

These gaskets and seals were relatively easy to get to. I replaced all 3. Put machine back together, but washer still leaked. I ended up having to remove more components down along the center shaft towards the transmission. I found that the "tub seal" was worn out. I also replaced the "seal nut assembly" and "O-ring" while I was at it. The seal nut and tub seal were more difficult to remove without the proper tool, but a bigger rubber mallet and strategically placed pliers were enough to break them loose. Once all parts showed up the washer went back together easily and it is now leak-free.

I unplugged the electric power cord and disconnected the two water hoses and the drain line from the wall. It was messy as water leaked from the disconnected hoses. I tilted the washer forward and leaned it against a bench for support. This exposed the bottom of the washer from the back. I removed the v-belt from the three pulleys. The motor mount was spring loaded making it easy to remove the v-belt from this pulley first. After removing the v-belt, I then removed the 4 screws to the small plate on the back of the washer to gain access to the water pump. I then removed the two water hoses from the water pump using vice grips to squeeze the clamps and slide them off of the hoses toward the water pump. After removing the two hoses (a little messy again), I removed the water pump by using a socket ratchet to loosen the four bolts. I replaced the water pump with the new pump and then reassembled everything in reverse order.

This was easy except for the e-ring which was extremely difficult to remove. When I put the new one on I filed down the bottom of the front edges to make it easier to slide it on. Beware: If you have the washer tipped back against the wall when you do get the e-ring off everything will come sliding off the shaft all at once and go everywhere. These parts are covered with black grease and made quite a mess so you might want to have someone hold them in place so you can gently slide them off one piece at a time.