LNC6760A71 Admiral Washer - Instructions

installed new pump, 10 min. job

Took the front panel off the washer with a screwdriver, tilted the washer back and propped it up with a paint can, unscrewed 2 nuts & bolts, disconnected the electric to the motor and lifted out, put the new motor in place & secured it with the nuts & bolts, reconnected the electric and re-installed the front panel of the machine and I was done.

Simply followed the instructions on the video provided and the repair was a breeze - quite impressive service!

I replaced the water level switch by taking loose the five screws on the back of the control panel, The clamp on the clear hose, and the two screws which went through the Wtr. lvl. switch. I also moved the wires from the old switch to the new, one at a time. This didn't fix my problem so i replaced the Water valve on the bottom-rear of the machine by removing the screw, the two hoses and the four wires. I removed these one at a time, moving the wires directly from the old valve and attaching them to the new valve.This fixed my problem good as new.

Removed and placed new one in 15 minutes. Thank You so much for the help

placed washer on front exposing bottom of machine. removed clip holding pulley in place with needle nose pliers. The old parts slid off transmission shaft easily. I set these aside in order of removal. The replacement parts were not exact matches to OEM parts replacement bearing was heavier duty and thicker there were washers in the kit that would not even slid onto transmission shaft,replacement pulley and cam were exact replacements for OEM. I replaced the bearing and thrust washer and then used a combination of new and old washers to build the assembly back to the original length so the retaining clip would hold assembly firmly in place.The instructions key point was that the final height had to bring the pulley back to the original height for a snug fit with retaining clip. Once I realized this the extra parts in the kit were less worrisome.

follow the video on snubber ring replacement an use 1/2 inch washers keep the tub springs from collapsing then it is very easy to remove them make sure to tilt the tube assembly an un hook start to finish under 1 hour

I did it just like a video was showing. This was really good instructional video.

Tilt washer back and pop belt on bottom of washer. Use putty knife to open top of washer 2 clips 2 inches in from both sides. Use racket to open and remove front panel of washer. use racket to remove 3 screws that hold pump to base of washer. pliers to remove clamps for intake and output hoses. use small bucket to catch water in hoses and pump. Replace pump unit, put screws in, put pump clamps on, put front panel back on , snap down top of unit, put belt back on pulleys and your done.

The video on PartSelect.com regarding replacing the washer machines drain pump with pulley was extremely helpful. By following the simple instructions as shown in the video, I was successful in replacing my washing machines pump in less than an hour, and saved myself the labor costs a repairman would have charged me for a really simple and easy repair job. I was also extremely happy and impressed with PartSelect.com. The price I paid for the part was very competitive and arrived within 3 days. I was very glad to see the pump and pulley assembly was a Whirlpool factory certified part and not a knock-off or reconditioned part.

I followed write ups on this web site and the job was straight forward. As far as the washer brake rotor I did not need to replace it. After removing the six screws that cover the assembly I noticed some rust and dirt so cleaned it with degreaser and reassembled it. I have no loud screeching sounds when the spin cycle comes to an end. As always PartSelect did a great job getting the correct parts to me with in a few days, thanks.

Removing and replacing the pump was a very easy process. Once the belt was removed on the bottom of the machine, I removed the back plate to gain access to the pump. Three screws and a couple of clamps holding the hoses on the pump. There was a little more water in the pump during removal than anticipated. Other than that, it was an easy fix.

The repair went smoothly with no issues or problems. The video link sent with the receipt made all the difference in the world. I watched the video on my iPad as I was doing the repair. Also locating the parts I needed on the part select website could not have been simpler.

Ordered two new hinge pins as well as hinges. (Did not want to have to deal with it again so chose a full change out.) Watched a U-Tube video that described how to change out the hinges. The trick is find out how to lift the top panel on the washer to access the screws that anchor the hinges. Use a putty knife and slide it into the space between the top panel and the front panel. Got the job done today in an hour or so. Chose to also wipe out the top of the wash tub at the same time so it took a bit longer. Works fine now. Just like new.

Took of lid,took out screws,put on hinge and pins,simple job