Quick Question!

Have you ever purchased from PartSelect.com before?

Models > LNC6760A71 > Instructions

LNC6760A71 Admiral Washer - Instructions

All installation instructions for LNC6760A71 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the LNC6760A71
256-270 of 380
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Broken water inlet valve

  • Customer: Gregory from Urbana, OH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
In our case, the hot water inlet valve was obviously broken. We picked up the washer on the side of the road in our neighborhood. We checked it out in our driveway - hooking it up to the water hose. When we connected to the hot side, water came gushing out the valve, inside the washer. A quick look confirmed it was obvioulsy broken. We connected the cold side and it started to fill the tub. Other checks confirmed the washer timer and other controls worked OK. we ordered the valve part from PartSelect (about $60 total). Took all of about 30 minutes to pull the old valave out and install the new one. Cleaned up the washer (it really needed it BADLY), and the washer is working perfectly now.

Washer wouldn't spin.

  • Customer: Charles from Sherrodsville, OH
  • Difficulty: Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
After reading several online posts about this problem on appliance forums and following the suggestions about how to determine what was needed (whether the inner tub turned freely (by hand) in spin mode or not. It didn't which apparently indicates the likely need for a new thrust bearing. I purchased the transmission pulley and bearing kit from Parts Select. I got it the next day, without asking for next day delivery! When I took the old parts off (easy: pull off the plastic cover, remove the circlip and everything falls off the shaft (if you are working with the washer just tipped up. Unfortunately, that was where my easy repair ended. The parts were entirely different! After looking and looking and thinking, I called Parts Select. They informed me that Whirpool, who makes Maytag had redesigned the parts. They didn't look like they would work, but I followed the directions which came with the kit and installed the new parts - three times. The last time the pulley stayed on and the washer spun as it ought. The problem was that even with the smaller of the spacer washers the circlip was extremely difficult to get in its slot. Anyway, now the washer works and I am pleased, even though I spent many hours on what ought to have taken perhaps 1/2 hour.

machine locked up

  • Customer: Fred from Batavia, OH
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Socket set
  • 0 of 0 people found this instruction helpful
removed belt motor and tub would turn and pump would not. ordered new pump removed three screws removed pump and reinstalled. washer works like new

Lid hinge on right side broken, lid hinge pin broken on left side

  • Customer: Layne from Waynesboro, VA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Watched video , after that there was no problem, really easy.

washing machine shakes and moves during spin cycle

  • Customer: Erich from Sheffield Village, OH
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set, Wrench set
  • 0 of 0 people found this instruction helpful
Had no problems taking machine apart following online instructions. At first couldn't find snubber ring because it was completely worn away. Once found it was very easy to replace. Only problem with putting back together was getting the first spring back on, after that it was a breeze. Machine up and running.

Won't Agitate, Won't Spin, Jumping around, squealing in spin cycle, abrupt stop

  • Customer: Gina from Los Angeles, CA
  • Difficulty: Really Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Washer was jumping around in the spin cycle to the point that it disengaged the water fill level hose which in turn caused it to overflow. I fixed the hose but almost immediateley it stopped spiining or agitating. I looked online to find that the jumping around was most likely the snubber ring ... the hard stop and squeal most likely the Brake Stator ... the no agitaion or spin was likeley the thrust bearing. I ordered the parts and were received in a couple of days ... by the time they came I had already torn apart everything and was just waiting on parts for reassembly. The instructions were concise and complete but I did benefit from watching a YouTube video on the repair. All the parts went together just like they were supposed to even with my limited mechanical skills. All I really used was a small socket set, a couple of screw drivers and a pair of pliers. Taking the Brake assembply is dangerous but can be done with no special tools if you buy a couple of 2 inch 10-24 screws to replace two of the short ones and then back them out slowly (look for a youtube video on this procedure EASY!) ... took me a couple of hours but any one who has used a screw driver more than once could probably do it in under an hour. Washer now running like new ... No Jumping!!! People at Parts Select were Great!!! BTW ... So that the springs would be easier to re-install, I stuck about $50 of quarteres between the coils before removing ... worked Great!

Broken hinge pin

  • Customer: Edwin from Bloomingdale, IL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
The repair was easy. 5 minutes after grabbing my tools the job was done. It was easy to find the part I needed on the web site.

alot of noise when spinning

  • Customer: Kathleen from High Point, NC
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Socket set
  • 0 of 0 people found this instruction helpful
..watched the video..easy as pie..took longer to figure out what part was making noise than to fix..

water wasnt draining and machine wasnt spinning, lots of noise

  • Customer: Paul from Phoenix, AZ
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
turned off the water, drained the water from the machine, pulled it out and removed the back plate on the machine. disconnected all hoses and belts, then removed part. inserted new pump, 3 self tapping screws later the hosed were attached, then the back plate. worked like a champ after that and saved me at least 200 bucks.

Washed hubby's overalls with a 6 in screwdriver in his pocket. Flooded the Kitchen and the basement.

  • Customer: Judy from Osceola, MO
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
We went on line and found the correct part. It arrived in 3 days. said it might take 7. Husband and son dismantled the old plastic outer tub that had been slit by the screwdriver. Put the new one in, and filled the tub up with water to check for leaks. When the water got to the level of the fill line, it started leaking. We pumped the water out and stopped to wait for daylight. Next day we lifted the top of the machine and filled it again...the line that goes to the water level knob...was off. The woman found the leak and put the hose back on. We were semi worried when we read the reviews, but in the daylight, it really wasn't all that difficult to change out the broken tub.

Drain pump broke

  • Customer: Robert from Buena Park, CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Socket set
  • 0 of 0 people found this instruction helpful
Remove front cover and fastened new pumpin .hooked up hoses pretty easy. The part was easy to order and was shipped really fast. Thanks for your

Lots of water on floor

  • Customer: Jim from Oxford, NC
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
Took access panel off of back saw that hose had pulled off of tub, thus the rinse water was just running on floor, re attached hose when the rinse cycle finished and the brake stopped the spin it jerked the hose off once again. It had a spring clamp holding it on, so I reinstalled it with a worm/screw clamp, no problems since. Ordered a new hose to have on hand in case. Jim

Pump noisy

  • Customer: robert from mont alto, PA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I pulled the back panel off, removed the belt and three 3/8 nuts holding the pump on.removed pump and installed new one, tests ok. It was easy for me I was a sears tech for two years on laundry equipment, nevertheless with your repair video it would be a breeze for a novice. Thanks for getting my part to me within two days. You guys are the greatest. - Sincerely, Mr Bob Byers

Nail stuck in pump, eventually seized up...

  • Customer: John from North Weymouth, MA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Socket set
  • 0 of 0 people found this instruction helpful
Simply replaced the pump: Disconnected 2 hoses, removed the pulley belt, swapped out the pump, replaced the hoses and belt, good to go !!

Noise and binding in drain pump

  • Customer: jerry from San Saba, TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
Remove 2 hoses and six bolts.replaced the belt and wash again.
All Instructions for the LNC6760A71
256-270 of 380