Quick Question!

Have you ever purchased from PartSelect.com before?

Models > LDF9932ST > Instructions

LDF9932ST LG Dishwasher - Instructions

Installation Instructions for parts on models starting with LDF9932ST

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

Models starting with LDF9932ST

All Instructions for models starting with LDF9932ST
1-15 of 30
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Broken door spring allows the door to overextend to the floor if not propped.

  • Customer: Gregory L from INDEPENDENCE, OH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 5 of 5 people found this instruction helpful
Simple, removed screws securing machine in the cabinet, then pull the unit out of the cabinet space about 10 inches. Springs are accessible within this extension. You need strong hands to extend the springs and attach them. Once attached, push machine back in place and re-install the anchor screws. In my situation, only one spring was broken, so the attached side revealed the correct slot to place the hook on the top position, the bottom position has a plastic lead for the spring, and that lead is attached to a rope to the door hinge. Note: Replace BOTH springs, even if only one is broken.

Dispenser wasn't closing

  • Customer: Kristyn from Downers Grove, IL
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 5 of 6 people found this instruction helpful
Unscrewed the screws, displaced the dispenser and re installed the screws

Two Rollers missing on lower tray.

  • Customer: Thomas from BOYNTON BEACH, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 4 of 6 people found this instruction helpful
Snapped the rollers on.

Supply line leaked afterwards. Had to replace it. Installers(Home Depot) had it rigged and now it is loose. Going to have to rig it somehow.

  • Customer: Mark from IRWIN, PA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Wrench (Adjustable)
  • 2 of 2 people found this instruction helpful
Loosened 3 screws and unhooked supply line and electric box and pulled it out.

Roller Assembly was broken

  • Customer: Dale from ITASCA, IL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 2 people found this instruction helpful
Took off the broken one and snap on the new one.

Door spring connector

  • Customer: Thomas from Palm coast, FL
  • Difficulty: Very Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
Pull the dishwasher out from underneath the countertop took 2 minutes unscrewed the panel on the side one minute put the connector on one minute screwed the panel back on 1 minute put the dishwasher back underneath the counter two minutes very easy job

The dishwasher door would fall open when opening if it wasn't lowered slowly.

  • Customer: Allen from N LITTLE ROCK, AR
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Wrench (Adjustable)
  • 1 of 2 people found this instruction helpful
I disconnected the power cord and the drain hose, with a nut driver, under the sink. I removed the bottom plate that covers the water connection under the dishwasher. With the water turned off I used an adjustable wrench to disconnect the water line. I open the door and disconnected the brackets under the counter top, with a phillips screwdriver, that hold the dishwasher in place. I pulled the dish washer out of its enclosure far enough to fully access the spring loaded mechanism to replace the "connector assembly". Then I put it all back where it belonged.. Go slowly and have patience.

Lg code indicated a faulty motor

  • Customer: richard from Johnsville, CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
First, PartSelect is great!; fast,& accurate. 1. Inside the dishwasher: remove trays. Remove (A050) lower water sprayer from bottom by pulling up. Remove (F191) top sprayer assembly by pulling away from clip holders. Remove (M110) by removing the holding screws. This part cover the whole sump and has kind-of an open screen circling the unit. Now you will see the white plastic impeller (M120) which is attached the the motor with one Phillips head screw. WARNING. The Phillips head screw (holding the impeller in place) is a REVERSE THREADED SCREW. Turn the screw CLOCKWISE to remove it. Then remove the impeller from the motor shaft. Underneath and outside the washer: Remove the bottom plate. Finally remove the motor by unscrewing the four holding screws and electrical wiring.

Broken Roller On The Lower Tray.

  • Customer: Mike from Leo, IN
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
These were a simple snap on item. It took longer to carry the parts from the porch that to install. Recently purchased house. Rollers were missing due to overload?? Removed the remaining roller pieces. Cleaned and straightened the axle shafts, spray lubed the tray and snapped the new pieces in place.

racks were rusted

  • Customer: dennis4417 from Albuquerque, NM
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
parts were not exact match with original, even though ordered from schematic. had to bend the replacement part slightly so it would fit into holder pieces. this took about 10 minutes as I was trying to be careful not to break/cut the coating (which would then lead to rust again). Once the piece was bent, just snapped the rack into place.

Door is to heavy to hold

  • Customer: Ricardo from Gilbert, AZ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
The connector assembly connects to a spring to hold the door from falling down. You need to disconnect the power cord, the water line and the drain hose before you move the dishwasher out the kitchen counter. There are several screws that hols the dishwasher in place top, side and bottom. Removed all screws then pull the dishwasher out very slow. Take the side panel by un-screwing all the screws around the panel in my case where five screws (two in the front so you have to open the door to get to them). You need to keep the door down to connect the assembly to the door bracket and the go through the pulley then to the spring, very easy. Put the side panel back and push the dishwasher in place use the same screws and reconnect the hose the water line and the power and you are done.

Led lamp burnt out

  • Customer: Aleksander from Wheeling, IL
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Replaced them

There was not enough pressure on the sprayers to clean the dishes. found the pump gasket cut in two and out of place.

  • Customer: Larry from Jacksonville, IL
  • Difficulty: A Bit Difficult
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I disassembled the upper parts of the pump housing and installed the new gasket. It seems to work fine now.

The error code HE showed up on the dishwasher and unit stopped before a full cycle was complete

  • Customer: Dwain from Pinedale, WY
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
When I read the book it said that the HE stood for Heating Element. You can easily get to it from the bottom. (leason learned after getting to it from the top) Test the element for continuity. Second Test to see if power is being fed to Heating Element with dishwasher turned off. Expensive Lesson Learned After Burning up three Heating elements (including the original) The Circuit board went bad and was sending power to my Heating element with dishwaher off. It was burning up the heating elements in about 30 seconds. $150 dollars of parts and shipping dishwasher is still not working. Waiting to see if LG will honor there 5 year warranty on the Control Board.

Dish washer would shut off mid cycle.

  • Customer: Richard from Camdenton, MO
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Check the motor and discovered roughness when you turned the shaft. I assume there was a bearing problem. I ordered a new motor from part select and upon the replacement washer is working great! Thanks part select, my part arrived in a timely manner and you guys saved me approx. $500. Thanx again. Richard Sansom
All Instructions for models starting with LDF9932ST
1-15 of 30