This dishwasher door hinge cable assembly connects the door to the spring. The door hinge cable and the door spring apply tension to the door to prevent it from dropping open too quickly. This part co...
The dishwasher roller assembly connects to the dishrack, and is located in the lower level of the dishwasher. It allows the dishrack to easily slide in and out. If the lower rack keeps falling off the...
The rack roller and axle in your dishwasher allows the dish rack to slide in and out effectively.If you notice that your dish rack is not performing this function, or if one or more of your rack rolle...
The door spring, used in dishwashers, adds tension to the door through the door hinge to keep it from opening too fast. If you have a door latch failure or your washer door drops too quickly when open...
This drain pump assembly is a genuine OEM replacement part for your dishwasher. In order to complete this repair you will need a Phillips screwdriver, pliers, and a socket. You will need to pull the d...
This is a door gasket for a dishwasher. It creates a watertight seal between the dishwasher door and tub to prevent leaking while the appliance is in use. The gasket is approximately 76 inches long an...
This nozzle assembly, commonly referred to as a sprayer head or spray arm, is an authentic replacement part supplied directly by LG for use in LG dishwashers. The nozzle assembly can be found at the b...
This diverter motor, or stepper motor, controls the movement of the spray arms in your dishwasher. It directs water between the drain pump and the spray arms by turning a check valve inside the pump, ...
This is the lower dishrack assembly for various models of LG dishwashers. This dishrack is an OEM part that is designed to hold dishes and cutlery during the wash cycle of the dishwasher. This dishrac...
$202.68
In Stock
Questions And Answers for LDF8874ST
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
2 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Terry
November 8, 2021
I need a drain pump assembly. Schmatics are confusing. I need the part number so as to order. Thanks, terry
For model number LDF8874ST
Hi Terry,
Thank you for your question. The part number listed under your model number for the drain pump assembly is PS11706890. If you would like to place an order for it, you may order it either online or by calling our customer service line and anyone will be happy to assist you. We hope this helps! If you have any questions, please let us know.
Water is leaking out of the bottom of the door. Is there a seal in the bottom? If so what is the #?
For model number LDF8874ST
Hello Lawanda, thank you for reaching out. Based on our research, we recommend you check the filter, part number PS7795137, at the bottom of the dishwasher and clean away any solid debris. Another easy way to maintain a clean filter and stop water leaking on the floor from your dishwasher is to clean off any solid food pieces before placing your dishes to wash. If the problem persists, we suggest inspecting the door gasket for tears, gaps, or cuts in the seal that could cause a dishwasher door leak. If found damaged, replace the door gasket, part number PS3522654. We hope this helps, good luck with this repair!
Simple, removed screws securing machine in the cabinet, then pull the unit out of the cabinet space about 10 inches. Springs are accessible within this extension. You need strong hands to extend the springs and attach them. Once attached, push machine back in place and re-install the anchor screws. In my situation, only one spring was bro
... Read moreken, so the attached side revealed the correct slot to place the hook on the top position, the bottom position has a plastic lead for the spring, and that lead is attached to a rope to the door hinge. Note: Replace BOTH springs, even if only one is broken.
According to your site, the part(s), to consider, to resolve the problem were: 1.Motor Assembly DC Pump, OR 2.Drain Pump. I simply selected the drain pump because it was cheaper and because it was making a clicking noise. (The only significant noise that this dishwasher was making) To be safe, I unplugged the unit and turned off the w
... Read moreater, under the sink. I removed the kick plate and I unscrewed the anchor clips from under the counter and carefully pulled the unit out. I then opened the dishwasher and removed the lower rack. To minimize water clean-up, I took a rag and soaked up the standing water in the bottom until it was nearly dry. I then tipped the dishwasher on it's left side, knowing where the location of the drain pump (front, right), would be in an easier location for me to work. I first unplugged the pumps wiring. Then, with pliers, I was able to disconnect the clips on the short, rubber hoses that hold the pump in alignment.(Use caution: If reusing the same rubber hose(s) on the new pump, it will be easier if you put them on in the same direction as they were take off) Then I removed the rubber supports off their hooks, that allow the pump to hang from the bottom of the dishwasher. Once the rubber hoses are re-connected on the new pump and placed on to it's former proper alignment, you can re-attach the rubber supports to their hooks. And last, but not least, remember to plug the new pump's wires back in place. Carefully stand up dishwasher and push it slowly back into place. I plugged in the unit and turned on the water. Before I screwed the unit back to the counter and kick plate back on the front, I ran a load and watched for leaks beneath the new pumps area. No leaks. "Easy, Peasy".
Shut off electrical breaker, Removed bottom cover plate by removing 2 Phillips head screws. I was able to remove the pump without pulling the dishwasher out by removing wiring connection, hose clamps with a pair of pliers, and removed the 2 rubber hangers However I couldn’t reinstall the pump without pulling the dishwasher out. 1.I disco
... Read morennected the electrical wiring (breaker was shut off). 2. Shut the water supply off and removed water line at the dishwasher. 3. Disconnected the drain at the sink. 4. Removed the 2 retaining screws 1 on each side that secures the dishwasher in place. 4. Removed the upper and lower racks, Used a shop vac and sucked the water out of the bottom of the dishwasher. 5. Pulled the dishwasher out making sure the drain line came with it. 6. Laid The dishwasher over on the back side to the floor. 7. Reinstalled pump with new hose clamps and hoses that came with the pump. ( it probably would have been easier to remove the pump with the dishwasher pulled out) reinstall the wire connection to the pump (snap in connection), connected the 2 new rubber hangers to pump and connected to the dishwasher . 8. Slide the dishwasher back in place and reconnect water line be sure and use some Teflon tape, reconnect electrical wiring, reconnect drain line, secure dishwasher with screws. Turn water on and check for leaks, turn electrical power back on. I ran the dishwasher to make sure it worked and make sure there weren’t any leaks before I installed the bottom cover plate. I had an appliance service person say that they wouldn’t work on an LG because they were hard to work on and very difficult to get parts. My experience was just the opposite thanks to partselect. The Dishwasher works like brand new.
