Quick Question!

Have you ever purchased from PartSelect.com before?

Models > LDF6810ST > Instructions

LDF6810ST (ASTEEUS) LG Dishwasher - Instructions

All installation instructions for LDF6810ST parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the LDF6810ST
1-15 of 32
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Broken door spring allows the door to overextend to the floor if not propped.

  • Customer: Gregory L from INDEPENDENCE, OH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 5 of 5 people found this instruction helpful
Simple, removed screws securing machine in the cabinet, then pull the unit out of the cabinet space about 10 inches. Springs are accessible within this extension. You need strong hands to extend the springs and attach them. Once attached, push machine back in place and re-install the anchor screws. In my situation, only one spring was broken, so the attached side revealed the correct slot to place the hook on the top position, the bottom position has a plastic lead for the spring, and that lead is attached to a rope to the door hinge. Note: Replace BOTH springs, even if only one is broken.

Dispenser wasn't closing

  • Customer: Kristyn from Downers Grove, IL
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 5 of 6 people found this instruction helpful
Unscrewed the screws, displaced the dispenser and re installed the screws

Two Rollers missing on lower tray.

  • Customer: Thomas from BOYNTON BEACH, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 4 of 6 people found this instruction helpful
Snapped the rollers on.

Roller Assembly was broken

  • Customer: Dale from ITASCA, IL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 2 people found this instruction helpful
Took off the broken one and snap on the new one.

Supply line leaked afterwards. Had to replace it. Installers(Home Depot) had it rigged and now it is loose. Going to have to rig it somehow.

  • Customer: Mark from IRWIN, PA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Wrench (Adjustable)
  • 2 of 2 people found this instruction helpful
Loosened 3 screws and unhooked supply line and electric box and pulled it out.

Door wouldn't close/lock wouldn't engage

  • Customer: Albert from MIDDLETOWN, NJ
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 1 of 1 people found this instruction helpful
Very easy repair. First remove all the screws from the inside of the door, making sure you support the outside part of the door with a pot under it on the floor. Pull the locker part out, remove wire connection with needlenose pliers, and install replacement part. Put door back together, and you're done.

Door spring connector

  • Customer: Thomas from Palm coast, FL
  • Difficulty: Very Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
Pull the dishwasher out from underneath the countertop took 2 minutes unscrewed the panel on the side one minute put the connector on one minute screwed the panel back on 1 minute put the dishwasher back underneath the counter two minutes very easy job

The dishwasher door would fall open when opening if it wasn't lowered slowly.

  • Customer: Allen from N LITTLE ROCK, AR
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Wrench (Adjustable)
  • 1 of 2 people found this instruction helpful
I disconnected the power cord and the drain hose, with a nut driver, under the sink. I removed the bottom plate that covers the water connection under the dishwasher. With the water turned off I used an adjustable wrench to disconnect the water line. I open the door and disconnected the brackets under the counter top, with a phillips screwdriver, that hold the dishwasher in place. I pulled the dish washer out of its enclosure far enough to fully access the spring loaded mechanism to replace the "connector assembly". Then I put it all back where it belonged.. Go slowly and have patience.

Lg code indicated a faulty motor

  • Customer: richard from Johnsville, CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
First, PartSelect is great!; fast,& accurate. 1. Inside the dishwasher: remove trays. Remove (A050) lower water sprayer from bottom by pulling up. Remove (F191) top sprayer assembly by pulling away from clip holders. Remove (M110) by removing the holding screws. This part cover the whole sump and has kind-of an open screen circling the unit. Now you will see the white plastic impeller (M120) which is attached the the motor with one Phillips head screw. WARNING. The Phillips head screw (holding the impeller in place) is a REVERSE THREADED SCREW. Turn the screw CLOCKWISE to remove it. Then remove the impeller from the motor shaft. Underneath and outside the washer: Remove the bottom plate. Finally remove the motor by unscrewing the four holding screws and electrical wiring.

Broken Roller On The Lower Tray.

  • Customer: Mike from Leo, IN
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
These were a simple snap on item. It took longer to carry the parts from the porch that to install. Recently purchased house. Rollers were missing due to overload?? Removed the remaining roller pieces. Cleaned and straightened the axle shafts, spray lubed the tray and snapped the new pieces in place.

Dishwasher leaks from door region during washing cycle.

  • Customer: tom from grass valley, CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
Old door seal appeared ok, no rips and seated evenly all around. Pulled that seal out and replaced with new. Seated new door seal after wetting inserted lip. Tested...leak greatly reduced, but still dripping. Removed seal, placed a rubber rope (same rope used for screening) within the tub recess, then reseated new seal. leak ceased. Also replaced the reservoirs on the left side of the cabinet (guide assembly). Old reservoir had debris within so decided to replace. Used regular pliers for the 3 hose spring clamps underneath, and a pair of large neede nose pliers for the fill flange (regular thread).

Broken guide wheels on top dishwasher rack

  • Customer: Joe from Poughkeepsie, NY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Pried old rollers with screwdriver. pushed (or 'pliered' new rollers, after straightening gudie pins, if necessary. One new roller broke a minute after installation, but I ordered extras because 6 odl rollers had alread broken), so we're OK for another year or so...

Door is to heavy to hold

  • Customer: Ricardo from Gilbert, AZ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
The connector assembly connects to a spring to hold the door from falling down. You need to disconnect the power cord, the water line and the drain hose before you move the dishwasher out the kitchen counter. There are several screws that hols the dishwasher in place top, side and bottom. Removed all screws then pull the dishwasher out very slow. Take the side panel by un-screwing all the screws around the panel in my case where five screws (two in the front so you have to open the door to get to them). You need to keep the door down to connect the assembly to the door bracket and the go through the pulley then to the spring, very easy. Put the side panel back and push the dishwasher in place use the same screws and reconnect the hose the water line and the power and you are done.

The error code HE showed up on the dishwasher and unit stopped before a full cycle was complete

  • Customer: Dwain from Pinedale, WY
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
When I read the book it said that the HE stood for Heating Element. You can easily get to it from the bottom. (leason learned after getting to it from the top) Test the element for continuity. Second Test to see if power is being fed to Heating Element with dishwasher turned off. Expensive Lesson Learned After Burning up three Heating elements (including the original) The Circuit board went bad and was sending power to my Heating element with dishwaher off. It was burning up the heating elements in about 30 seconds. $150 dollars of parts and shipping dishwasher is still not working. Waiting to see if LG will honor there 5 year warranty on the Control Board.

Broken roller axle rack clips

  • Customer: Mark from Euless, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Be sure to order extra rolled with axles. The clips the snap on to the top rack are delicate and I broke two of them putting them in place. Be sure to snug them on slowly and carefully, it seems that the soap scum buildup on the rack creates additional friction. This friction makes you need to push the part on harder, and when you do it snaps on too hrs and one side of the clip will break off.
All Instructions for the LDF6810ST
1-15 of 32