Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
The drum support roller (Dryer Drum Support Roller, Drum Roller and Washer Assembly) holds the drum in the proper position while it spins on the support wheels. This part rotates on the roller shaft w...
$13.45
In Stock
Order within the next 1 hr and 45 mins and your part ships today!
The tumbler and motor belt in your dryer allows the drum to spin during the drying cycle. At 100 inches in length, this dryer drum belt is 3/8 of an inch wide and has five ridges. The belt is black in...
$32.30
In Stock
Order within the next 1 hr and 45 mins and your part ships today!
The front glide is located at the front of the dryer, the drum rides along it. If you hear a metal-on-metal noise when your dryer is running, your front glide may be worn out and require replacing. Th...
$14.65
In Stock
Order within the next 1 hr and 45 mins and your part ships today!
This roller shaft is also known as a support roller shaft or a drum roller axle, and is a part for your dryer. The function of this piece is to act as the axle for the drum roller; it provides a place...
$9.77
In Stock
Order within the next 1 hr and 45 mins and your part ships today!
This comes with a metallic hub clamp to hold it firmly in place. The blower wheel with clamp is part of your dryer assembly. You will find this part attached to the drive motor shaft, which disperses ...
$22.86
In Stock
Order within the next 1 hr and 45 mins and your part ships today!
This part is a retaining ring, sometimes called a retaining clip, that holds the drum support roller onto the shaft of a dryer. It is made entirely of metal and measures less than an inch in diameter....
$7.85
In Stock
Order within the next 1 hr and 45 mins and your part ships today!
This is a replacement lint filter for your dryer. Replacing this part is easy as it requires no disassembly of the unit. Make sure to clean the filter after every use of your dryer, and check the filt...
If you notice that your dryer is noisy or will not tumble, then you may need to replace the drum roller shaft washer. This drum roller shaft washer is just under an inch in diameter and is sold indivi...
$13.74
In Stock
Order within the next 1 hr and 45 mins and your part ships today!
This door catch kit is designed for use in dryers. This is an authentic OEM replacement part. This catch assembly ensures the door of your appliance will close, and remain closed. It allows your appli...
$32.22
In Stock
Order within the next 1 hr and 45 mins and your part ships today!
This part replaces two terminal switches in a dryer and prevents the dryer from running when the door is open. This includes two connectors. If your dryer will not shut off, start, or does not tumble,...
$29.84
In Stock
Order within the next 1 hr and 45 mins and your part ships today!
Questions And Answers for LDE7304ACE
Ask our experts a question about this model and we'll get back to you as soon as possible!
2 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Dale
September 5, 2021
Dryer will heat on setting more dry but not on time setting.
For model number LDE7304ACE
Hello Dale, Thank you for the question. this could indicate an issue with the Timer. This dryer timer is used to control the unit's cycles by regulating the length of time that power is directed to each setting and the Element. We hope this helps!
I replaced 2 belts in less than a week because my dryer keeps breaking them any suggestions?
For model number LDE7304ACE
Hello Wilfredo, thank you for contacting us. If your dryer is consistently breaking belts, there are a few potential issues you might want to investigate:
1. Alignment Issues: Ensure that the drum and pulleys are properly aligned. Misalignment can cause the belt to wear unevenly and break.
2. Overloading: Make sure you are not overloading the dryer. Excessive weight can put extra strain on the belt.
3. Obstructions: Inspect the drum for any obstructions or foreign objects that might be causing the belt to snag or wear prematurely.
4. Tension Issues: Ensure that the belt tension is correct. If the tension is too loose or too tight, it can lead to premature belt failure.
5. Compatibility: Ensure you are using belts that are compatible with your dryer model.
If you have checked these areas and the problem persists, then we would suggest checking the idler pulley wheel, part number PS11743028, to solve the problem. If the idler pulley wheel is worn out or not functioning smoothly, it can cause excessive friction on the belt. We hope this helps.
Removed the front cover (screws on bottom 0f face)...removed blower cover....spring pliers to remove and install blower fan. the rest of the time was spent cleaning the inside of the shell as well as the vent. Reassembled and dryer runs better than it has for many years.
1. Removed front of machine (2 screws at the bottom). 2. Removed 4 screws from inside the dryer, to take off the blower housing. 3. Removed 4 screws and took out the large metal piece which supports the drum at the front. Removed the drum. 4. Replaced the two rollers that support the drum in the rear. Cleaned the pins they
... Read morerun on, and oiled very lightly. Also replaced the idler roller. I was surpirsed to see that these rollers use plain bearings, not ball bearings. 5. On the front support piece, drilled out the rivets for the glides, and replaced the worn out glides with new parts. Applied a little glue (3M weatherstrip adhesive) to the cork pieces, to glue them to the metal. Attached the plastic pieces over the cork pieces, and riveted in place using rivets that came with the glide kits. 6. Replaced front and rear felt seals. This was not as tricky as I expected it to be. They were held in by metal tabs. Glued the ends where they came together. 7. Replaced the felt blower seal. Glued to the blower housing. 8. Reinstalled the drum, installed new belt, which came with good instructions (luckily). 9. Reassembled front support piece and the front of the cabinet.
I also cleaned the lint from the cabinet and from the vent hose.
In general, the job went without a hitch, and the machine probably has quite a few years left, despite the fact that it's 18 years old. This gives me a good feeling.
I'd say this would be challenging, though, for someone who is not pretty experienced with machinery repair. Also, the cost of the parts was significant enough that it would not have been unreasonable to have opted for a new machine.
