LAT8804AAL Maytag Washer - Overview
Sections of the LAT8804AAL
[Viewing 8 of 8]Keep searches simple, eg. "belt" or "pump".
Belt Kit
PartSelect #: PS2005284
Manufacturer #: 12112425
This kit includes both the drive belt and the pump belt which are both V-shaped. If your washer does not toss, spin, or drain water properly, this might be because one of these belts has worn or stret...
$41.21
In Stock
Mounting Stem/Tub Seal Kit
PartSelect #: PS2351899
Manufacturer #: 6-2095720
This kit comes with a hub assembly, agitator seal, and spanner nut. If your washer leaks once it is full (with or without clothes in it) or leaks during agitation, then you should replace the seal. Th...
No Longer Available
Screw
PartSelect #: PS12349731
Manufacturer #: W11233072
This is a multi-use and multi-appliance screw. It can be used on a microwave, refrigerator, range/oven, air conditioner, dehumidifier, washer, or dryer. The measurements of this screw are 8 x 1/2 inch...
$20.77
In Stock
Screw, 8/18 x 3/8
PartSelect #: PS11746840
Manufacturer #: WP90767
This screw is sold individually.
$5.41
In Stock
Lid Switch
PartSelect #: PS11723153
Manufacturer #: W10820036
This 3 prong lid switch is used for washing machines that do not have a tub light.
$23.67
In Stock
Hose Clamp
PartSelect #: PS11743008
Manufacturer #: WP596669
This hose clamp is used in a wide variety of household appliances. Most often it is found in washers, dishwashers, refrigerators, freezers, dehumidifiers, garbage disposals, or air conditioners. This ...
$11.77
In Stock
Drain Pump
PartSelect #: PS11743017
Manufacturer #: WP6-2022030
This washing machine drain pump is intended for use with automatic washers that have been manufactured since 1958. The pump itself is made of plastic, though it does come with a metallic belt pulley.
$82.79
In Stock
Rubber Foot Pad
PartSelect #: PS11738859
Manufacturer #: WP210684
The leveling leg pad or foot pad fits over the leveling leg on your washing machine. The foot pad is designed to protect your floor and keep the washing machine level and in place. This foot pad is ju...
$15.24
In Stock
Washing Machine Lid Hinge Ball
PartSelect #: PS11738871
Manufacturer #: WP211726
This washing machine lid hinge ball is well under an inch in diameter. These hinge balls are sold separately, though two are required per lid. This lid hinge ball is made of plastic and is used for Ma...
$11.13
In Stock
Tub Bearing Kit
PartSelect #: PS2347235
Manufacturer #: 6-2040130
This kit is used on 2-belt washers. It is recommended to change the seal kit at the same time. The tub bearing kit fixes issues with leaking, loud noise, excessive shaking/moving or if your pump is no...
$55.54
In Stock
Lid Check Switch
PartSelect #: PS11738787
Manufacturer #: WP207166
This lid switch check is used in washers to detect if the washer lid is open or closed. This prevents a cycle from spinning when the lid is still open and is also used to start your washer once a cert...
$48.36
In Stock
Lid Switch Assembly
PartSelect #: PS11739302
Manufacturer #: WP22001682
This black lid switch assembly comes complete with a bracket, two switches, and a fuse. An open fuse might indicate that the lid switch is bad. The point of the lid switch is for the tub to stop spin...
$42.38
In Stock
Questions And Answers for LAT8804AAL
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the LAT8804AAL
[Viewing 12 of 12]Leaking
Fixed by
these parts
these parts
Show All
Burning smell
Fixed by
these parts
these parts
Show All
Will not drain
Fixed by
these parts
these parts
Show All
Will not agitate
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Spins slowly
Fixed by
these parts
these parts
Show All
No hot or cold water
Fixed by
these parts
these parts
Show All
Lid or door won’t close
Fixed by
these parts
these parts
Show All
Spinning Issues
Fixed by
these parts
these parts
Show All
Shaking and Moving
Fixed by
these parts
these parts
Show All
Won’t Start
Fixed by
these parts
these parts
Show All
Noisy
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Drum would not drain and there was a banging noise when the drum spun
I removed the 2 phillips screws on the bottom of the front panel. Then checked around to find the belts were actually below the floor panel.
I pulled the washing machine away from the wall and tilted it bacwards and found the pump belt was off the pully and the drive belt was badly damaged. I replaced the 2 belts which took no tools ... Read more and about 3 minutes to accomplish then resecured the front panel, pushed back in place and leveled. Complete repair from diagnosis to back in operation took less than 15 minutes.
I pulled the washing machine away from the wall and tilted it bacwards and found the pump belt was off the pully and the drive belt was badly damaged. I replaced the 2 belts which took no tools ... Read more and about 3 minutes to accomplish then resecured the front panel, pushed back in place and leveled. Complete repair from diagnosis to back in operation took less than 15 minutes.
Read less
Parts Used:
-
Charles from Whitman, MA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver, Screw drivers
584 of 636 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
water leaking from around center shaft below fixed tub
My washer is 5 years old and water began to leak on the floor. I took off the front panel and filled the tub. Water did not leak immediately, but after the tub filled with about 3-4 inches of water, the water began to leak from a rubber washer between the fixed tub and the drive shaft. I looked online for exploded diagrams of Maytag wa
... Read more
shers, when I came across your site. By looking at your diagrams, I determined what parts I needed and ordered them. The parts arrived in 2 days, and I installed them. There were no leaks and it cost me under $70 (a repairman would have cost at least $250). The only thing I would recommend to those in similar situations, is to purchase a spanner wrench (your site does not sell, but others do). The stem seal and hub assembly is reverse threaded (clockwise to loosen) and is difficult to remove due to tight quarters in the tub.
Read less
Parts Used:
-
douglas from bonita springs, FL
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Nutdriver, Pliers, Socket set
526 of 548 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Leaking water
Well, I found the washer leaking water from the bottom a couple weeks ago. I finally got around to pulling off the front panel and ran a couple cycles to see where the water was coming from. Turns out the leak was at the plastic pump that does the draining after wash and rinse.
So I got the model number and googled online. I ... Read more found Partselect and they had every part I needed. Took me 10 minutes online to find the parts for my specific washer. I couldn't believe how easy it was. Parts came in two days...and this was right before Xmas.
Anyways, changing out the pump was simple. Took 5 minutes to get it off and put the new one in. I decided to change the hoses and elbow siphon break as well while I had the thing apart as those parts were old...but still working well.
Got the washer back together and the floor is dry as a bone. Perfect repair, really easy to do. Hardest part was figuring out how to get the front panel off.
So I got the model number and googled online. I ... Read more found Partselect and they had every part I needed. Took me 10 minutes online to find the parts for my specific washer. I couldn't believe how easy it was. Parts came in two days...and this was right before Xmas.
Anyways, changing out the pump was simple. Took 5 minutes to get it off and put the new one in. I decided to change the hoses and elbow siphon break as well while I had the thing apart as those parts were old...but still working well.
Got the washer back together and the floor is dry as a bone. Perfect repair, really easy to do. Hardest part was figuring out how to get the front panel off.
Read less
Parts Used:
-
Joseph from Plano, TX
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers
203 of 230 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!