KUIC15NLTS0 KitchenAid Ice Maker - Instructions

(1) Ordered PS371704 from PartSelect! Best advice EVER! (2) Unplugged refrigerator (since the water solenoid on the back of the refrigerator is powered to switch ON the water, you NEVER have to turn off the water!) (3) Pull off the refrigerator's bottom grill. (4) With a small saucer under the fittings, unscrew the black and white tube fitting. There is only one nut to remove on the white tubing side. You'll need to undo the compression fitting on the black tubing and slide off the compression nut. You'll need to MAKE SURE you keep these nuts and replace onto the black and white tubing the SAME WAY you took them off. You'll NOT need to use nut drivers as finger tight is the key. Too hard and you'll ruin these plastic nuts. You should get only about 1/8 cup or less of water during this whole exercise. (5) Cut off the old, broken water nozzle. (4) Find a screw of the appropriate size to fit tightly 1/2 way inside the new tubing (this is to ensure your old and new tubing are connected to feed through the door). If screw is not tight within the tubing, wrap part of a plastic (thin) sack around this screw a couple of times and force into the tubing. You'll, of course, then need to use the hacksaw to cut the head off the screw as you'll be forcing the other half of the screw into the old cut tubing (6) Chase the dog out of the kitchen and cajole your wife (significant other) to push the newly joined tubes through the top of the dispenser, through the door and out the bottom as you will be gently PULLING on this old tubing from the bottom until the new tubing pops through the doors bottom. (7) Once this new tubing is out, you will separate the old tubing and, using the nuts in the proper sequence, connect this new tubing to the white tubing. (8) Plug the refrigerator back in and test flow the water. Check to ensure the plastic nuts have no leakage ... button up the bottom grill ... and enjoy the fresh water! PS> Don't forget to praise the wife (significant other) and give the dog a treat for staying out of your face!!

Removed broke wire and replaced new wire. Use gloves to pull the wire tight. That's very important.

I thought the water bucket wasn't holding water because the icemaker continually was running - however, the crack didn't go through. The real issue was the Thermostat.

You've got to be able to sit or kneel and fit both arms in the unit for a while, so if you've got patience and ability, you can do it. If you have a battery operated screw driver with a nut and 6 star nut remover, this goes quicker.
Do not throw your old plug away, it doesn't come with a new one.

The hard part was getting the black thing (that attaches to the icebucket) back on. I had to go to Lowes and get a gasket and silicone grease to replace the one on it. I thought this was the reason it wouldn't go back on, because the gasket wouldn't fully fit back into the white hole.
I measured the diameter of that hole compared to the old one. It was slightly smaller and was not as smooth as my old one (it had manufacturing form lines and excess plastic that hadn't been removed)
I Dremeled it to increase the diameter, especially where the gasket was buckling out when trying to fit it on.
I finally got the black part back on.

I found later that it was cheaper somewhere else, however shipping charges are less and most parts are next day delivery.
I just ordered the thermostat. Wish me luck!

Removed and replaced sensor

Just install the new valve by reversing the process of removing the old valve. Only possible nance is with the quick release hose fittings - the collar is pushed down to release the hose. Also, be sure to FULLY reinsert the hose in the new valve. Best to twist the hose a bit when inserting so it goes through the o-ring inside the valve. If not fully inserted, it will leak.

I was anticipating that the fan would be facing the back of the refrigerator. It actually was perpendicular to the back. There was some difficulty removing the bolts of the fan. I persevered and was victorious.

I took out old grid and removed the top broken wire. I attached the end of new wire to the terminal screw and carefully threaded the new wire back and forth without kinks. I was not able to get wire as tight as it was originally, but able to get it tight enough with pliers. I attached the other end to the opposite terminal screw. I had plenty of wire for the job and cut off the excess. I re-installed the grid and had ice the following morning. Feeling good about myself and saved a lot of money.

Found fault with recirculating pump. Found hot spot on pump circuit board . Replaced pump

I replaced the two pumps, since both were the same design...figuring if one went bad then the other would soon go bad...and then I also replace the water level sensor. All had quick connect plugs. The time is just taking apart the various pieces, cleaning, installing the new pumps and sensor, then reassembling.

replaced handle

It was worth the money for that little screw, since I didn't have to run all over trying to find the right one.

Received replacement valve ~ 3 days, easily replaced in less than 15min, works great

Simple to replace. Next fall I will be sure to drain the outdoor icemake and shut it down for the winter.

After turning off water to icemaker, defective control removed (two screws) and new unit installed.Worked perfectly.I was totally amazed when I ordered the part thursday afternoon and it arrived fridaY morning.Total time out of operation less than 24 hours.Wonderful results.

UPS delivered the part at 11:05 AM and I had it installed in less than 30 minutes. No issues, easy removal and re-installation although the compartment was very tight for my hand and a 1/4" drive socket wrench. One installation suggestion however, pre-thread the 3 mounting screw holes on the motor housing first by screwing one of the screws provided into each of the three mounting holes on the motor housing prior to attempting to install the new motor. This way you'll find it much easier to get start the screws given the very limited work-space behind the fan compartment.