Quick Question!

Have you ever purchased from PartSelect.com before?

Models > KUDS30FXSS1 > Parts

KUDS30FXSS1 KitchenAid Dishwasher - Parts

All parts for the KitchenAid Dishwasher KUDS30FXSS1

Below is a list of all parts for the KitchenAid Dishwasher KUDS30FXSS1. To find the repair part you need, you can browse the list below or you can narrow your choices by searching for a part by name or description.

All Parts for the KUDS30FXSS1
1-14 of 198
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$38.54

Rack Adjuster Kit - Left and Right Side

The rack adjuster connects to the dishrack and is used to change the height of the rack. This kit includes the parts to replace the left and right-side rack adjusters and has been ...

$20.70

Wheel

The lower dishrack wheel is used in a dishwasher to easily roll rack back and forth on the rails. To repair, open the dishwasher door and pull out the lower dishrack. Next, push the tab from both sides and it should pop out. To install the new wheel assembly, place it on the rack and make sure the caps overlap the wire from the inside before you clip it in place by pushing the wheel. Slide the rack back in the washer to make sure it is installed correctly. Refer to the manual provided by the manufacturer for further instructions.

$17.53

Door Balance Link Kit

This part is a door balance link kit, also sometimes known as door cable or door spring cable kit, that helps support the door as it opens and closes by connecting to the dishwashe...

$4.74

Rack Stop Clip

This part goes on the end of the rail to stop the dishrack from falling out.

$5.07

Tine Pivot

The tine pivot clip, also known as the tine row pivot, is used in dishwashers and is located in the upper dishrack. The clip is used to keep the tine row in place in the dishrack. ...

$11.43

Mounting Bracket

The mounting bracket is sold individually, without screws. This part secures the upper side of the dishwasher to the underside of the counter or cabinet to prevent the dishwasher from moving, shaking, or tilting forward. The bracket is made entirely of metal. It is recommended to check all brackets, if applicable, because they often wear at the same rate and both may need to be replaced. This is an OEM part that is sourced from the authentic manufacturer. Tools needed are a pair of needle nose pliers and a screwdriver.

$17.31

Chopper Assembly

This is a chopper assembly or drain food chopper, and it is designed for your dishwasher. The chopper chops up/minces the food particles in your dishwasher to prevent them from clo...

$26.28

Tine Row

The tine row on your dishwasher rack divides the rack into columns to keep your kitchen items in place during the washing cycle. If you notice that one or more of the tines on your current tine row is damaged, you should consider replacing it. This product is made of gray plastic and is approximately 21 inches in length. This tine row contains 11 straight tines and 1 curved tine. This product is sold individually. Many of our customers have rated this repair as very easy. To complete this repair, simply remove the old tine row and replace it with the new one.

$31.97

Drawer Track

$14.69

Spinner Kit

This is also called the 3rd-level spinner. This part works like a little spray arm at the top of your dishwasher.

$31.38

Positioner

Also known as rack adjuster. Sold individually.

$15.34

Rinse Aid Cap

This part holds the rinse aid liquid in the dispenser until the timer activates the rinse cycle.

$23.13

Adjuster Clip

Sold individually.

$4.89

Rubber Washer

The rubber washer is a part which is specific to dishwashers and should not be substituted by a similar part. It works with the heating element to seal the receptacle opening where the heating element is attached. The rubber washer is used to prevent water leaking from your dishwasher during its cycle. Before making any repairs to your dishwasher make sure that you disconnect the power by finding the breaker for the dishwasher, and turning it off. The tools you will need to complete this repair include an adjustable wrench, and a 1/4 inch nut driver. This specific rubber washer is sold individually.

All Parts for the KUDS30FXSS1
1-14 of 198